Problem with Dreambox 600 Remote - URC-39930RJ0-04

marmelad · Post by **marmelad** » Sat May 12, 2007 7:19 am

I have built a JP1.X interface and run ir700beta3 but when i try to read the remote i get this message

There is a conflict at fixed data adress $0200. Do you wont to replace the existing data with the fixed data?

What should i do to read the remote?

binky123 · Post by **binky123** » Sat May 12, 2007 7:36 am

The latest software is IR7.00 from here.

IR7 is successfully reading the data but the fixed data it expects to see is different. You should choose NO and then save the .IR file and upload it into the Diagnostics section. Most likely, some of the fixed data has changed and I need to reduce the number of "fixed" bytes in this remotes RDF.

marmelad · Post by **marmelad** » Sat May 12, 2007 7:50 am

Now i have upload it https://www.hifi-remote.com/forums/dload ... le_id=4571

Post by **The Robman** » Sat May 12, 2007 10:06 am

I took a peek at the RDF and I don't understand why it calls for fixed data, so hopefully someone more familiar with this remote can explain. I would think that it would be OK for you to comment out the fixed data section of the RDF (ie, put a # in front of both the entry and the header)

#[FixedData]
#$0200=$4B,$4E,$53,$01,$05,$04,$07,$FF,$FF,$FF,$02,$2C,$10,$51,$20,$01,$00,$04,$00,$07

binky123 · Post by **binky123** » Sat May 12, 2007 10:07 am

Thanks. I've looked at it and it doesn't share any common data between the other .IR files. I've removed the [FixedData] section from the RDF and uploaded the new version here.

marmelad · Post by **marmelad** » Sat May 12, 2007 11:57 am

I have try the new file and now i can download from the remote but i dosent get any data in the Devices whay?

binky123 · Post by **binky123** » Sat May 12, 2007 1:12 pm

The devices tab is only for device upgrades that you upload via IR7. What did you want to do or what are you looking for?

marmelad · Post by **marmelad** » Sat May 12, 2007 2:06 pm

I wont to change the signals so i can use 2 dreambox with 2 remotes .Becasue now if i change channel it change on both dreambox

binky123 · Post by **binky123** » Sat May 12, 2007 10:03 pm

The .IR file you uploaded had these device upgrades using protocol 016C and Fixed Data in the hidden upgrade area:
SAT/0031: 0E 07 44 1A
SAT/0032: 0D 17 44 1A
SAT/0033: 0C 27 44 1A
SAT?0034: 0B 37 44 1A

You'll need to find a way to change the "unit" number on the DM600 so it responds to 0032,0033 or 0034. You then change the remote setup code to be 0032,0033,0034.

You can use RM to build an upgrade if you want as well. It appears the hex code for buttons are the same but the fixed data is different between dreambox machines.

The hidden SAT/0031 device upgrade is

Code: Select all

Upgrade Code 0 = 28 01 (SAT/0031) DM600
6C 00 FE FE FE E2 FE C0 04 06 E1 0E 07 44 1A 00 
00 01 00 02 00 03 00 04 00 05 00 06 00 07 00 08 
00 09 00 0A 00 0B 00 44 00 0D 00 0E 00 0F 00 50 
00 51 00 52 00 28 00 20 00 53 00 21 00 22 00 23 
00 24 00 25 00 26 00 40 00 41 00 42 00 43 00 0C 
00 27 00 45 00 54 00 60 00 61 00 62 00 63 00 64 
00 65 00 66 00 67 00 68 00 69 00 35 00 30 00 31 
00 32 00 33 00 34 00 
End

marmelad · Post by **marmelad** » Sun May 13, 2007 4:53 am

I wont to change the remote like this

Code: Select all

SAT: 0031 Orginal
	
#   Key Name    Hex Commnd    EFC
1   0           00 00         19141
2   1           01 00         17093
3   2           02 00         23237


SAT: 1238 that i wont to change to

#   Key Namn    Hex Command    EFC
1   0           10 00          51909
2   1           11 00          49861
3   2           12 00          56005

I have make an upgrade with RM and i gave it the setup code 1238. I cant change the setupcode for the dreambutton. I change it to 1238 but when i read the remote again it has change back to the orginal setupcode.
The Dream Setup Code Lock is off. What does i do wrong? what should i use for setupcode?

binky123 · Post by **binky123** » Sun May 13, 2007 8:01 am

I would need to see your .IR file to be sure but your remote resets the DREAM device when it can't find a device setup code. Perhaps there is a mismatch between the setup code specified on the DREAM device button and the setup code used in the device upgrade?

marmelad · Post by **marmelad** » Mon May 14, 2007 11:20 am

where can i upload it?

Capn Trips · Post by **Capn Trips** » Mon May 14, 2007 1:01 pm

In the Dianosis Area of the Files Section. There is an

button at the top of the page. It's the same place you uploaded a file in the third post of this thread. How did you upload THAT one?

marmelad · Post by **marmelad** » Mon May 14, 2007 2:49 pm

It didn't know if it was allowed to upload that file there, but here is the file
Ir file

binky123 · Post by **binky123** » Tue May 15, 2007 8:39 am

I don't see anything unusual in your .IR file. I noticed your fixed data in your SAT/1238 upgrade is 06 0F 44 12 which is different than what SAT/0031 uses. Is this correct?

Also try a different setup code number. So when you download from the remote again, the only difference between upload and download .IR files is the DREAM setup code changes back to SAT/0031, correct?