Insignia service menu

jackching · Post by **jackching** » Sun Jun 25, 2023 8:09 pm

Is there any info here on how to enter an Insignia service menu? I have two problems i cant resolve. The overscan doesnt seem to be set correctly as the screen seems cut off and also when there is a power outage or power is cut from the unit, the tv will turn on when the power is re applied. Neither can be set in the normal menu. The tv is probably 15 years old but still works.

Post by **The Robman** » Mon Jun 26, 2023 7:46 am

In case it differs by TV model, it might help if you mention the model number, and whether it's a Roku set or not.

Try this:
1. Power on
2. set the volume to 0
3. press: INPUT, 9876, OK

Or, try this:
1. Power on
2. set the volume to 0
3. press: INPUT, 1147, OK

For a Roku set, try this:
1. Power on and go to Home menu
2. Press HOME 5 times
3. Press: FFWD, PLAY, REWIND, PLAY, FFWD

jackching · Post by **jackching** » Mon Jun 26, 2023 12:10 pm

I tried those and they didnt work. I figured there may have been a discrete or something for them. It's a non smart LCD panel. Model: NS-L322Q-10A

MaskedMan · Post by **MaskedMan** » Mon Jun 26, 2023 12:22 pm

Back then the code the tv uses and whose tv brands its from it was good chance that you manufacturered it. It was standard answer to insignia questions was direct them to Emerson, Mitsubishi, or Phillips. So whose code does your tv respond to?

https://www.remotecentral.com/cgi-bin/m ... cgi?7632,3

Post by **The Robman** » Mon Jun 26, 2023 4:55 pm

jackching wrote:It's a non smart LCD panel. Model: NS-L322Q-10A

I don't see that model in the file section, how are you controlling it, are you using an upgrade or a built in setup code?

jackching · Post by **jackching** » Tue Jun 27, 2023 10:06 am

I am using the built in code that comes with the URC-3660.

HamburgerHelper1 · Post by **HamburgerHelper1** » Tue Jun 27, 2023 4:17 pm

Try: This
With TV POWERED OFF
MUTE
1
8
2
POWER

Does your remote have colored buttons? Red /Blue/ etc?
On the remote - press
7
red key
9
blue key
then you can enter into factory mode menu. After entering into factory mode menu, sign of the factory menu M will appear

Post by **The Robman** » Tue Jun 27, 2023 5:11 pm

jackching wrote:I am using the built in code that comes with the URC-3660.

Which prompts the obvious question, which setup code are you using?

jackching · Post by **jackching** » Tue Jun 27, 2023 5:49 pm

The Robman wrote:
jackching wrote:I am using the built in code that comes with the URC-3660.
Which prompts the obvious question, which setup code are you using?

Good question. I just used the simplest method by holding down the 2 key and it took right away.

MaskedMan · Post by **MaskedMan** » Tue Jun 27, 2023 9:57 pm

You can blink back the code:

1. tv
2. press and hold SETUP for two blinks, release
3. enter 9 9 0
4. press the #1 key, count the blinks
5. press the #2 key, count the blinks
6. press the #3 key, count the blinks
7. press the #4 key, count the blinks

Now post the 4-digit code.

jackching · Post by **jackching** » Wed Jun 28, 2023 5:25 am

Is there a way to save the current setup on this remote? I actually use it on another setup and was just trying to get this tv to work with it. 986 doesnt save the configuration on this remote. The last time i had to redo it all. I could hook it up to the cable i guess.

HamburgerHelper1 · Post by **HamburgerHelper1** » Wed Jun 28, 2023 6:35 am

The save config command for the 3660 is 968. But it works a little different than 986
Hold setup until 2 blinks then enter 968 then enter a 4 digit code of your choice.
there will be 2 blinks confirm.Command 977 will restore your config

HamburgerHelper1 · Post by **HamburgerHelper1** » Wed Oct 18, 2023 7:03 am

Is there a way to save the current setup on this remote? I actually use it on another setup and was just trying to get this tv to work with it. 986 doesnt save the configuration on this remote. The last time i had to redo it all. I could hook it up to the cable i guess.

Is that a typo "986" or is that what you entered ?
The save config is "968" and if "968 does not work it means it is set and then disabled
the only way to reset is using RMIR