View previous topic :: View next topic |
Author |
Message |
MJ
Joined: 28 Sep 2003 Posts: 25
|
Posted: Tue Nov 25, 2003 8:37 pm Post subject: General Instruments DRC400 limitations?? |
|
|
With standard manual programming it has limited functionality (Sony, setup code 0000 no menu access...). This is what the local cable company Gogeco (big in Canada) supplies with digital cable. It really needs a JP1 doctor. It is also apparently on its way to being replaced by Motorolla DRC450 which at least has holes.
In an attempt to upgrade my friends DRC400 I have just loaded the latest(?) IR321b and the RM/IR compliant RDFs. I'm unable to get macros anywhere.
On a nother note, as a test; using KM I was able to upgrade the EFCs for discrete pwr on/off onto the "Bypass" and "Music" buttons. IR devices page indicates that the EFCs are not on the buttons where I placed them and the numerous keymoves showed scrambled EFCs as well.
Using RM there was no effect as the buttons did not appear transmit a signal. This may merely take some experimentation as it is my first day with RM. However there my be a bug with both IR and RM when it comes to this remote.
It seems there's a lot of organization and new releases happening wrt RDFs, RM, IR and KM so If it's better to wait for the dust to settle I will.
In the meantime I can plug away at it, but it would be helpful to know what would qualify as the shift key on the remote? The manual programming sequence merely involves holding down the device key for a few seconds. I used IR to make macros on shifted keys then used the "setup" (aka shift??) in another macro in an attempt to invoke one, but nope.
Thanks in advance
Matthew |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Tue Nov 25, 2003 8:45 pm Post subject: Re: General Instruments DRC400 limitations?? |
|
|
MJ wrote: | However there my be a bug with both IR and RM when it comes to this remote. |
More likely, there's a problem with the RDF. The DRC400 doesn't get a lot of press around here, so it's likely we don't know enough about it (yet). _________________ Mark |
|
Back to top |
|
|
Castlestone
Joined: 08 Nov 2003 Posts: 7 Location: Nova Scotia |
Posted: Tue Nov 25, 2003 8:51 pm Post subject: |
|
|
MJ
I've tried to create a macro on the DRC450 but have run into the same problem as you in that they just don't work. I gave up for now but I would like to be able to do it.
Mike |
|
Back to top |
|
|
gjarboni Expert
Joined: 20 Sep 2003 Posts: 294 Location: Columbia, MD |
Posted: Tue Nov 25, 2003 9:30 pm Post subject: |
|
|
There are some JP1 remotes that don't support macros. The Maestro II is one that I'm absolutely sure doesn't do macros. The remote that came with the Replay 2000's also fits that category (I think). The best way to test is to try to create a macro from the remote. If that isn't described in the manual (or you don't have the manual) then look on this site at the 15-1994 or Cinema 7 manual. What ever the 9xx code is for creating macros I believe it's the same across all the S3C8 non-LCD remotes. If that doesn't work you are almost 100% certainly out of luck. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21238 Location: Chicago, IL |
Posted: Wed Nov 26, 2003 10:16 am Post subject: |
|
|
The macro code is 995, but while Jason's advice is generally correct, some further clarification is needed.
Some remotes only allow manually programmed macros on specific buttons, and those buttons aren't always present on the remote itself. One such example is the Outlaw Audio remote. In this case, the 995 command is accepted, but when you chose a button it is rejected. For a remote like this, you can program macros using IR.exe to almost any button.
Another example is the URC-6131 PVR remote. I don't recall if the 995 command is even accepted on this remote, it certainly doesn't allow manually programmed macros, but again you can program them with IR.exe _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
jamesgammel Exile Island Resident
Joined: 03 Aug 2003 Posts: 394 Location: Gillette, Wyoming |
Posted: Wed Nov 26, 2003 10:19 am Post subject: |
|
|
*P* (setup, set, magic, et al)(hold for two blinks), 9,9,5 is the typical macro programming sequence for non-lcd remotes. You may want to review those manuals anyway for the rest of the steps.
Jim |
|
Back to top |
|
|
MJ
Joined: 28 Sep 2003 Posts: 25
|
Posted: Wed Nov 26, 2003 5:09 pm Post subject: I think its missing "stuff" inside |
|
|
Thanks for the replies. DRC does not accept much. The manual states it will accept 990 to verify setup codes digit by digit. I tried other codes but she does not accept anything else. Next attempt involves liposuction AND colagen.
Moving on,
Matthew |
|
Back to top |
|
|
|