Page 1 of 2
Xoro 7550 and smart cx 72
Posted: Sun Mar 23, 2014 7:30 am
by Rathsach
Anyone who has the bin files for these cable boxes ?
Posted: Sun Mar 23, 2014 9:42 am
by alanrichey
Couldn't find the Xoro 7550, closest I could find was the Xoro 7520. Hopefully it uses the same codes
https://www.hifi-remote.com/forums/dload ... e_id=12448
The Smart CX72 is a pretty standard box, try this remote:
https://www.hifi-remote.com/forums/dload ... e_id=12447
But the instructions are well out of date so use the new instructions I put in with the Xoro Remote.
Posted: Thu Mar 27, 2014 6:41 am
by alanrichey
So what happened ? Spent quite some time on this, didn't expect to be ignored ?
Posted: Wed Apr 02, 2014 6:39 pm
by Rathsach
Thanks a lot.
I will test it tomorrow. The file attached for the CX doesn't see to be a bin file, does it work anyway?
Posted: Thu Apr 03, 2014 12:56 am
by alanrichey
As I said in my post, it's a box that uses the same codes.
Posted: Sat Apr 05, 2014 3:22 am
by alanrichey
So what happened ?
Posted: Sun Apr 06, 2014 6:31 am
by Rathsach
Well, the 7520 doesn't seem to work.
The file for the CX72 is a .RMDU file, which I can't upload to my 350, because it can't accept anything else than PL files
Maybe I'm doing something wrong with the last one, any suggestions?
Posted: Sun Apr 06, 2014 7:41 am
by alanrichey
My fault, now updated with the BIN files. As for the 7520, check the README.TXT file (The clue is in the name, you are supposed to read it)
Posted: Sun Apr 06, 2014 8:28 am
by Rathsach
Hmm, I've changed both files to other names (V2013_pl.bin and C2011_pl.bin) to give them different names to avoid the upload bug. I can upload the files, but none of the boxes responds.
A have a Denver box that works fine, but it has no card reader, arhgggg.
I'm about to use my slingbox as target for my bulldozer!!!
Posted: Sun Apr 06, 2014 9:22 am
by alanrichey
You can't just change the names, the code is embedded in the file.
I've recompiled them as C2014 & V2015
https://www.hifi-remote.com/forums/dload ... e_id=12465
Posted: Sun Apr 06, 2014 9:49 am
by Rathsach
It doesn't work. I tested both the files.
Well, you spent quite some time - I apreciate
But I don't know what to do.
Posted: Sun Apr 06, 2014 10:03 am
by alanrichey
Still not reading the instructions I see
Posted: Sun Apr 06, 2014 10:22 am
by Rathsach
Promise, I read all of it
What I'm a doing wrong?
I can make your denver 108 work with the 110. I'm doing it the same way. Maybe I'm reading it wrong or miss a important point???
Posted: Sun Apr 06, 2014 10:51 am
by alanrichey
Rathsach wrote:It doesn't work.
Quote from instructions:
"...If you have problems please do NOT just report back it 'doesn't work', that is totally useless for someone trying to understand what is going on. So please report the following:..........."
I rest my case
Posted: Sun Apr 06, 2014 11:10 am
by Rathsach
He he,
Well, as i wrote earlier the problem is, that the reciever (dvb-c box) doesn't respond = it doesn't work. I uploaded the files and there was no problem doing that. Therefore I don't know what to do or try next or what I'm doing/reading wrong?