Xoro 7550 and smart cx 72

Rathsach · Post by **Rathsach** » Sun Mar 23, 2014 7:30 am

Anyone who has the bin files for these cable boxes ?

alanrichey · Post by **alanrichey** » Sun Mar 23, 2014 9:42 am

Couldn't find the Xoro 7550, closest I could find was the Xoro 7520. Hopefully it uses the same codes

https://www.hifi-remote.com/forums/dload ... e_id=12448

The Smart CX72 is a pretty standard box, try this remote:

https://www.hifi-remote.com/forums/dload ... e_id=12447

But the instructions are well out of date so use the new instructions I put in with the Xoro Remote.

alanrichey · Post by **alanrichey** » Thu Mar 27, 2014 6:41 am

So what happened ? Spent quite some time on this, didn't expect to be ignored ?

Rathsach · Post by **Rathsach** » Wed Apr 02, 2014 6:39 pm

Thanks a lot.

I will test it tomorrow. The file attached for the CX doesn't see to be a bin file, does it work anyway?

alanrichey · Post by **alanrichey** » Thu Apr 03, 2014 12:56 am

As I said in my post, it's a box that uses the same codes.

alanrichey · Post by **alanrichey** » Sat Apr 05, 2014 3:22 am

So what happened ?

Rathsach · Post by **Rathsach** » Sun Apr 06, 2014 6:31 am

Well, the 7520 doesn't seem to work.

The file for the CX72 is a .RMDU file, which I can't upload to my 350, because it can't accept anything else than PL files

Maybe I'm doing something wrong with the last one, any suggestions?

alanrichey · Post by **alanrichey** » Sun Apr 06, 2014 7:41 am

My fault, now updated with the BIN files. As for the 7520, check the README.TXT file (The clue is in the name, you are supposed to read it)

Rathsach · Post by **Rathsach** » Sun Apr 06, 2014 8:28 am

Hmm, I've changed both files to other names (V2013_pl.bin and C2011_pl.bin) to give them different names to avoid the upload bug. I can upload the files, but none of the boxes responds.

A have a Denver box that works fine, but it has no card reader, arhgggg.

I'm about to use my slingbox as target for my bulldozer!!!

alanrichey · Post by **alanrichey** » Sun Apr 06, 2014 9:22 am

You can't just change the names, the code is embedded in the file.

I've recompiled them as C2014 & V2015

https://www.hifi-remote.com/forums/dload ... e_id=12465

Rathsach · Post by **Rathsach** » Sun Apr 06, 2014 9:49 am

It doesn't work. I tested both the files.

Well, you spent quite some time - I apreciate

But I don't know what to do.

alanrichey · Post by **alanrichey** » Sun Apr 06, 2014 10:03 am

Still not reading the instructions I see

Rathsach · Post by **Rathsach** » Sun Apr 06, 2014 10:22 am

Promise, I read all of it

What I'm a doing wrong?

I can make your denver 108 work with the 110. I'm doing it the same way. Maybe I'm reading it wrong or miss a important point???

alanrichey · Post by **alanrichey** » Sun Apr 06, 2014 10:51 am

Rathsach wrote:It doesn't work.

Quote from instructions:

"...If you have problems please do NOT just report back it 'doesn't work', that is totally useless for someone trying to understand what is going on. So please report the following:..........."

I rest my case

Rathsach · Post by **Rathsach** » Sun Apr 06, 2014 11:10 am

He he,

Well, as i wrote earlier the problem is, that the reciever (dvb-c box) doesn't respond = it doesn't work. I uploaded the files and there was no problem doing that. Therefore I don't know what to do or try next or what I'm doing/reading wrong?