JP1 Remotes

Just for reference, I found two posts at Remote Central that deal with the protocol mentioned in the original post in this thread...

IR code distorted when copied to PENG:
http://www.remotecentral.com/cgi-bin/mb ... d.cgi?6152

IR code bad in TSU3000, works fine in TSU2000:
http://www.remotecentral.com/cgi-bin/mb ... ad.cgi?799

zulfi wrote:Hmm - then my guess was wrong. Then the remote for LK's home automation system doesn't work for their dimmer as well...

The learned file is here:

https://www.hifi-remote.com/forums/dload ... le_id=6565

Regards
Rasmus

EDIT:
I forgot to mention, that all your work, including all the tools and the knowhow is really awesome. This site is in deed a gift to all OFA-remote fans... Thanks!

Hi,
I know this is a very (very) old thread, but this learned file is exactly what I am looking for to get my remote controlling this dimmer, unfortunately the link doesn't work anymore . I'm not using JP1 (sorry guys ), reason why I would like to find the hex. (I guess the hex codes are part of this "learned file", correct?).

I have tried with the hex mentioned above, but I experience the exact same behaviour than you described.

By advance, thanks a lot for your help

I'm not sure why the file with the learned signals is missing, but it would have been in UEI format rather than Pronto Hex. However, the upgrade Rasmus uploaded can be converted to Pronto Hex:

Button 1
0000 006D 0000 0018 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 052F 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0D2F

Button 2
0000 006D 0000 0018 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 052F 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 0D2F

Button 3
0000 006D 0000 0018 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 0030 0010 052F 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 0030 0010 0D2F

Button 4
0000 006D 0000 0018 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 0030 0010 0030 0010 052F 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0010 0030 0030 0010 0010 0030 0010 0030 0010 0030 0010 0030 0010 0D2F

I must say that I didn't expect a so quick answer on such an old topic! Thank you very much 3FG, I'll try that out tonight

I'd like to thank again 3FG for his prompt response to my request , these hexs work as expected.

Just for information, if someone in the future tries to get this Lauritz Knudsen dimmer to work with an Infra Red blaster from GlobalCache (iTach) and end-up on this page, then you must set a repeat value >2. I.e., the key "1" will be, with a repeat value of 4:
sendir,1:3,1,38000,4,1,16,48,16,48,16,48,16,48,16,48,16,48,16,48,16,48,16,48,48,16,16,48,16,3800