View previous topic :: View next topic |
Author |
Message |
hummbie
Joined: 21 Sep 2004 Posts: 9 Location: Vienna, Austria |
Posted: Tue Sep 21, 2004 10:24 am Post subject: Controlling X10 with RF signals |
|
|
Hi there.
I am looking for a JP1 Remote able to control my X10 equipment with RF signals - not IR. I already have a TM13 tranceiver (european version).
Do you think that RS 15-2117 will do the job? |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Tue Sep 21, 2004 2:37 pm Post subject: |
|
|
You'll need an IR543 to convert the IR signal from the remote to the X10 powerline signal. The RF capabilities of JP1 remotes are ONLY for use with their respective command centers. They cannot be used to control other RF devices (there is no such thing as a universal RF remote). _________________ Mark |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21254 Location: Chicago, IL |
Posted: Tue Sep 21, 2004 3:20 pm Post subject: Re: Controlling X10 with RF signals |
|
|
hummbie wrote: | I am looking for a JP1 Remote able to control my X10 equipment with RF signals - not IR. |
As long as that is a hard and fast requirement, it's not possible. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
hummbie
Joined: 21 Sep 2004 Posts: 9 Location: Vienna, Austria |
Posted: Sat Sep 25, 2004 3:58 am Post subject: |
|
|
Thank you for your replies but IR543 will not work in europe (you know 220V)...
I think I found the proper (rather expensive) european module: IR7243. It doesn't look the same but does exactly the same job - converts IR signals directly into X10. It should be compatible with Philips Pronto remotes.
There is also a cheaper solution: Powermid to convert IR signals into RF signals (such as those send by X10 remotes) but I am not sure if this would work for me. What do you think? |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21254 Location: Chicago, IL |
Posted: Sat Sep 25, 2004 8:51 am Post subject: |
|
|
Well, you could get a voltage converter to step your 220v down to 110v (you know, the kind of thing that travellers often need) or you could get an IR543 box and attempt to modify it to use an external power supply, like what Paul King did in order to use an RF extender box in the UK.
Read this...
http://www.hifi-remote.com/forums/viewtopic.php?t=2935 _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
mr_d_p_gumby Expert
Joined: 03 Aug 2003 Posts: 1370 Location: Newbury Park, CA |
Posted: Sat Sep 25, 2004 10:52 am Post subject: |
|
|
There might be a problem with trying to use a voltage converter on the IR543. Remember that it also has to inject the X10 PLC signals into the power line, and the voltage converter may block them. I would imagine the IR543 could be modified to work on 220v as it uses the same capacitor-zener type power supply as most other X10 stuff, but the bigger question is will it work on 50 Hz? hummbie wrote: | There is also a cheaper solution: Powermid to convert IR signals into RF signals (such as those send by X10 remotes) but I am not sure if this would work for me. What do you think? | No, this won't work for X10. The X10 IR signals are completely different from the X10 PLC signals on the power lines, and they are both different from the signals X10 uses for RF. Also, the Powermids will not be tuned to the same frequency as the X10 RF receivers. _________________ Mike England |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21254 Location: Chicago, IL |
Posted: Sat Sep 25, 2004 4:33 pm Post subject: |
|
|
mr_d_p_gumby wrote: | There might be a problem with trying to use a voltage converter on the IR543. Remember that it also has to inject the X10 PLC signals into the power line, and the voltage converter may block them. |
That's a good point. That might also rule out using a seperate AC transformer like what Paul did in the other thread I linked to. The best solution would probably be to modify the unit to run on 220v, assuming the 50hz thing isn't an issue. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
pgk
Joined: 21 Aug 2004 Posts: 113 Location: London |
Posted: Sun Sep 26, 2004 4:13 am Post subject: |
|
|
I've seen various guides on converting US modules to European voltages by changing 5-10 components, but none specfically covering the IR modules.
But the impression I've had is that if buying components "retail", then by the time you've paid for the shipping from the US and the cost of the components it's not always that much cheaper, especially if your not 100% certain what you are doing and since it's non-isolated mains electricity can be difficult/dangerous to test.
I found the 7243 module here for £32 + shipping.
Paul |
|
Back to top |
|
|
hummbie
Joined: 21 Sep 2004 Posts: 9 Location: Vienna, Austria |
Posted: Mon Oct 04, 2004 10:23 am Post subject: |
|
|
It has almost the same price as the unit I found in Belgium. Actually the point is that I don't like pointing the remote to some unit in order to switch on the lights. Think of a long macro involving more then one X10 commands. And besides I already have a RF remote which works fine with this receiver. I am looking for a better solution!
So, I have now another idea... I opened my KR22 - "Credit Card" Keyfob RF Remote and found a small transistor like RF transmitter inside.
It's obvious that this component ensures the proper frequency/modulation to carry out the X10 signal to the TM13 RF receiver. I wonder if it can be used for the RS 15-2117 remote to make it RF compatible to the TM13 RF receiver. What do you think? |
|
Back to top |
|
|
pgk
Joined: 21 Aug 2004 Posts: 113 Location: London |
Posted: Mon Oct 04, 2004 12:20 pm Post subject: |
|
|
> I wonder if it can be used for the RS 15-2117 remote to make it RF compatible to the TM13 RF receiver.
Probably not, as far as I am aware the 2117 puts all the data onto the carrier RF signal, including the IR modulation, I would doubt that X10 works like that. But maybe some who knows the hardware you have and the 2117 would be able to better comment.
Regarding the not wanting to aim the remote at the IR receiver whilst running macros this is where remotes like the 2117 with a separate command centre come in useful. Line the IR output of the Command Center up with the X10 IR receiver in somewhere out of the way. The RF transmit from the 2117 to the Command Center will then operate the X10 IR receiver. |
|
Back to top |
|
|
captain
Joined: 10 Jan 2007 Posts: 1
|
Posted: Wed Jan 10, 2007 10:33 am Post subject: IR *conversion* |
|
|
I have a (albeit now dead) device that will convert any IR transmitter into an RF transmitter. It's called a LeapFrog. I got it circa 1995 and used it, duct taped to the front of my RadioShack 6in1 AV Remote to control all my AV/HT gear, as well as my X10 system from *anywhere in the house*! It was a ridiculous hack but it worked great.
Hey! It may still exist! Check it out and give me some amazon.com credit for the referral.
http://www.amazon.com/dp/product/B00006JQJQ?tag=j0df-20
PS: It seems that by now someone should have created a WI-FI enabled Universal Remote Controller - perhaps as a PDA application, so one could simply have his cell-phone/PDA/RemoteControl in a pocket and have access to everything via ONE wireless medium. Now that I've invented the concept, watch someone else make a million with it in about 5-10 years. (story of my life |
|
Back to top |
|
|
|