Radio Shack 15-2137 Help Needed

[garytjia]

I just purchased a radio shack 15-2137 universal remote and had it setup to work with Marantz SR7200 receiver. However, it does not have the component type input switch available (e.g. DVD, CD, DSS, etc.) to allow switching between different components for sound output. I am still learning how to program the remote. Does anyone know how I could program the remote to include the input switch function?

This is a continuation of this thread...
http://www.remotecentral.com/cgi-bin/mb ... d.cgi?5159

Thanks

[kupakai]

Welcome to this forum. Did you get the DVR functions (from your post in remotecentral.com) to work? I should have asked you first which device code you have set for the that, and if you have tried all of them.

As for the receiver, I'll ask the same question; what device code did you set it on, and did you try all of the listed ones?

[garytjia]

No, I have not tried all the listed device codes for Marantz receivers...I will try them out. Thanks.

[irs009]

From what I've seen on these forums, and my own experience, the inputs often are found on the number keys. As you try all of the setup codes, be sure and check those for your inputs.

Jack

[Capn Trips]

It would be easier to provide you with detailed recommendations if you would use the mandatory template in the "Number 1 Code Search FAQ", linked in my sig below. Not knowing what setup code you are using makes it a bit harder to do so.

This file is an upgrade for your exact receiver. It has discrete input commmands. This upgrade uses the RC-5/5X combo protocol, used by built-in setup codes AUDIO/1089 and 1189, but the device codes are not identical.

It's also possible to generate about 2/3 of your device's signals using the RC-5 protocol, used in AUDIO/0189 (or possibly 0222 or 0269). I'm not sure whether the setup code you are using will support adding those commands via advanced code (EFC). If you're using AUDIO/1089 or 1189, here is the list of 5-digit EFCs:

Code: Select all

EFC	Functions
31289	num 0
31293	num 1
31281	num 2
31285	num 3
31273	num 4
31277	num 5
31265	num 6
31269	num 7
31257	num 8
31261	num 9
29305	vol up
29309	vol down
29197	mute
31417	channel up
31421	channel down
28793	up arrow
28797	down arrow
28781	left arrow
28769	right arrow
28785	select
29345	sleep
31441	exit
29189	display
62149	Input: TV
06853	Input: VCR
66245	Input: DSS
53957	Input: LD
29281	BassUp
29285	BassDn
29273	TrebleUp
29277	TrebleDn
29361	S. Direct
29361	Source Direct
28785	Menu On
28789	Menu Off
31253	F/P
31237	DMode
31297	seek up
31301	seek down
31405	Stereo/Mono
31389	Memo
31381	Preset Scan
31373	FM
31361	AM
31365	LW
31429	Input: Tuner
30937	PTY
25285	Input: TAPE
37573	Input: CD
08901	Input: CDR/MD
60756	AUX
60820	DVD
03364	A/D
03332	6 CH IN
27684	Power On
27668	Power Off
35892	Mute On
35876	Mute Off
19508	Display
36404	Multi-Room
37172	Dolby/Prologic
39268	Test Tone
33060	Ch. select
33044	Ch Up
33028	Ch Down
33188	Dolby
33172	Night
33172	Night Mode
33156	ATT
33252	Auto
33236	DTS
35236	6-Stereo
35284	CS 5.1
35284	CS Mus
35268	DSP
60724	PL2-mov
60708	PL2-mus
60692	CS Cine
60726	AF

Depending on what setup code you are using, most of those codes should work (except likely the last one).

If you are using a different setup code, the EFCs might be different.

It would be really easy if you used JP1, but pending development of the rdf for the 2137, I'm not sure what more you can do or try.