Panasonic PT AE900 device upgrade file

krisdz · Post by **krisdz** » Sun Feb 19, 2006 11:35 am

Hi
I’m working on the device upgrade file for the Panasonic PT-AE900.
I learn the signals form the Panasonic remote to URC8910.
In KM I create upgrade file as per:
http://www.hifi-remote.com/jp1/help/
Then uploaded it to my Outlaw 990 remote and guess what it is not working.
The protocol used in KM is Panasonic2 (LCD)
The protocol reported in URC8910 was Panasonic2
I’m not sure that those two are the same.
Here is my device upgrade file:
https://www.hifi-remote.com/forums/dload ... le_id=2817
Any help will be appreciated
Regards
Kris

underquark · Post by **underquark** » Sun Feb 19, 2006 2:16 pm

There could be a number of reasons for this not working. It would be helpful if you could also upload your IR files - the first one with the learned signals and then the one after you installed the upgrade but couldn't get it to work.

Post by **ElizabethD** » Sun Feb 19, 2006 2:47 pm

Couple ideas
You used some beta version of KM, is that OK?
The KM upgrade is for Outlaw, not 8910 - did you change the remote brand? Edited: I gather it should be Outlaw, right?
If one Panasonic2 protocol doesn't work, try the other - ther ought to be two possibilities in both RM and KM
[Panasonic2 (LCD-Hacked)]
[Panasonic2 (LCD-Official)]

krisdz · Post by **krisdz** » Sun Feb 19, 2006 4:22 pm

Hi Liz
The beta is OK I used it for the OPPO upgrade and it works.
I changed the remote to Outlaw. It is protocol isuee.
Regards
Kris

krisdz · Post by **krisdz** » Sun Feb 19, 2006 4:38 pm

Here are the requested IR files
Outlaw remote with Panasonic ae900 upgrade
https://www.hifi-remote.com/forums/dload ... le_id=2830

urc8910 remote with learned signals from Panasonic ae900
https://www.hifi-remote.com/forums/dload ... le_id=2829

Regards
Kris

Post by **ElizabethD** » Sun Feb 19, 2006 8:06 pm

You never said really what's not working

The Outlaw IR file indicates upgrade type is TV. But KM upgrade is SAT. I suspect this would cause problems. Also, but this may be my problem, when I open the Outlaw IR file, IR is objecting that the RDF might have an incorrect learned address except I don't think this file is meant to have learned signals.

Protocol used is 109, Panasonic2 official. Likely OK - but I know too little about protocols to meddle in this one. This needs EXPERTS.

The 8910 IR file containing learned signals: The few learned functions match a projector I once looked at (PT-L6500U), except for the Enter key, assuming that Enter was learned on the Enter button.

Edited: I just saw your thread where Greg and Whompus were making you a new RDF for RM, so ignore my above note about the RDF as I'm using an older set.

krisdz · Post by **krisdz** » Sun Feb 19, 2006 9:30 pm

Hi Liz,
Nothing is working; I mean there is no response from Projector to any IR signal sent from Outlaw remote.
All other component responds to Outlaw remote. Cable box, DVD, CD, preamp. Etc.
Regards
Kris

Post by **ElizabethD** » Mon Feb 20, 2006 8:30 am

I still think it's device type mismatch. Did you try changing it?

whompus · Post by **whompus** » Mon Feb 20, 2006 10:02 am

Upload the ir file from the 8910 that has the learned signals in it and put a link to it here.

Post by **ElizabethD** » Mon Feb 20, 2006 10:05 am

Whompus, he did - see his post Sun Feb 19, 2006 4:38 pm

whompus · Post by **whompus** » Mon Feb 20, 2006 10:09 am

Ahhh. My bad, I overlooked that.

krisdz · Post by **krisdz** » Mon Feb 20, 2006 10:19 am

I try it as TV and OEM. Otherwise what it could be?
Kris

whompus · Post by **whompus** » Mon Feb 20, 2006 10:33 am

Does the 8910 operate it with the learned functions?

Post by **ElizabethD** » Mon Feb 20, 2006 3:41 pm

krisdz wrote:I try it as TV and OEM. Otherwise what it could be?
Kris

IF I'm correct that it's mismatch of type, you could just change type in IR general tab , try it, it's simpler than changing the upgrade.

Mark Pierson · Post by **Mark Pierson** » Mon Feb 20, 2006 4:57 pm

krisdz wrote:I try it as TV and OEM.

The upgrade file you posted is set for SAT/0392. The Outlaw IR file you posted contains a CBL/SAT/0392 on the Devices tab, but the CBL button is set to TV/0392 on the General tab. Try setting the CBL button to CBL/SAT.