device specfic macros

leesweet · Post by **leesweet** » Tue Nov 18, 2003 12:02 pm

Here you go...

http://groups.yahoo.com/group/jp1/files ... 031118.txt

Thanks for your help!

Mark Pierson · Post by **Mark Pierson** » Tue Nov 18, 2003 6:54 pm

leesweet wrote:suffice it to say that I did all the above with 1.17 and still no-go.

I took a look at your file and don't see a Key Move for the DSM. Did you try step #7 that I outlined above?

7) On the Key Moves tab, create the key move on the Sat/Guide button, specifying TV/1103 as the Device Type and Setup Code. Click the Hex Cmd radio button and enter B6 as the EFC/Hex Cmd (this MUST be entered as a Hex Cmd or IR will think it's an EFC).

sfhub · Post by **sfhub** » Wed Nov 19, 2003 5:50 am

leesweet wrote:Here you go...

http://groups.yahoo.com/group/jp1/files ... 031118.txt

Thanks for your help!

See if this works:
http://groups.yahoo.com/group/jp1/files ... 031119.txt

leesweet · Post by **leesweet** » Wed Nov 19, 2003 1:54 pm

Thanks for the work,, however: (1) It does't work (only does 'info' not 'guide/guide/down/select') and (2) appears to be the exact the same changes as a version I sent you. (I *diid* do a KM also...)

Argh! Now what?!

Mark Pierson · Post by **Mark Pierson** » Wed Nov 19, 2003 5:04 pm

leesweet wrote:(I *diid* do a KM also...)

There wasn't a key move in the file you uploaded.

Try setting up a key move for the guide function on a phantom button and then specify that phantom in the macro. I think the fact that the macro uses the guide button is causing a conflict.

sfhub · Post by **sfhub** » Thu Nov 20, 2003 12:31 am

leesweet wrote:(I *diid* do a KM also...)

IR didn't show any keymoves for the file you uploaded.

I think Mark is correct and the usage of "guide" both as a keymove/DSM
and being referenced in the shift-guide macro was causing a loop. I was
focused on the missing keymove for DSM didn't even notice it until
he pointed it out. I fixed that and uploaded the file again.

http://groups.yahoo.com/group/jp1/files ... 031119.txt

leesweet · Post by **leesweet** » Sat Nov 22, 2003 12:35 pm

Well, that doesn't work at all. Using that downloaded file, 'Guide' (when in 'guide' mode as usual) brings up the usual Replay Guide (VCR/0617).

Any more ideas? Thanks for all the help!

Mark Pierson · Post by **Mark Pierson** » Sat Nov 22, 2003 12:47 pm

leesweet wrote:'Guide' (when in 'guide' mode as usual) brings up the usual Replay Guide (VCR/0617).

Ok, what mode is the remote in? I think what you wrote above is incorrect and you meant to say "Replay" mode, correct?

If so, open the file in IR. Go to the Key Moves tab and change the Bound Device on the Key Move from SAT to whatever device button your Replay is on. Upload that to the remote and try it.

leesweet · Post by **leesweet** » Sat Nov 22, 2003 3:53 pm

Ick, user error..

Since 'Guide' is also Guide for Replay. I'm all AFU'd up. Workaround: 'Sleep' for the Custom Guide, M1/M2 for changing from 4:3 to 16:9, and M3 for all power toggle until I get to better answers.

Thanks for all the work!