View previous topic :: View next topic |
Author |
Message |
ToddF
Joined: 31 Dec 2003 Posts: 26 Location: Hampton Roads, VA |
Posted: Mon Jan 12, 2004 9:17 pm Post subject: Philips 30PW862H widescreen HDTV upgrade created |
|
|
I have created an upgrade for the Philips 30PW862H widescreen HDTV and uploaded it into the yahoo files area. Enjoy...
Todd F. |
|
Back to top |
|
|
Alric
Joined: 01 Feb 2005 Posts: 4
|
Posted: Tue Feb 01, 2005 11:32 pm Post subject: |
|
|
Hi Todd,
I am having problems using the upgrade; most likey due to my inexperience with JP1.
My problem is that I can not produce a valid protocol ID within keymap master. I enter the parameters as in the upgrade file:
Devices:,RC-5,0,100,3
But I don't know how to enter these:
Manual:,,0 = 1-byte,LSB-COMP,86,NO
And this is how this part looks in KM;
Protocol ID: ## ##
Fixed Data: FF D9 3F
Manual Settings
Enter PID: RC-5
2nd Cmd Byte: None
Signal Style: LSB-COMP
Bits/Dev: 3
Bits/Cmd: 8
Any thoughts would be greatly appreciated. Thanks for the file! |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Wed Feb 02, 2005 5:49 am Post subject: |
|
|
Alric wrote: | But I don't know how to enter these: | You open upgrade files by using the LOAD button on KM's Setup sheet. There's no need to re-enter any of the info. _________________ Mark |
|
Back to top |
|
|
Alric
Joined: 01 Feb 2005 Posts: 4
|
Posted: Wed Feb 02, 2005 7:41 am Post subject: |
|
|
Something may be wrong with my set up because after loading the file and selecting the remote the parameters are not filled in automatically.
A "code" is not produced and I get an error after I load the file and specify the remote:
Filename: Philips_30PW862H_widescreen_HDTV-tf_ver2.txt
*** Unsupported or unrecognized Protocol ***
Enter Device Codes and/or Raw Fixed Data (hex). Enter the Protocol ID and set the options in the Manual Settings table. Use the Notes section to enter any 3rd-Party Protocol Code.
On the protocol ID section I get:
Invalid Protocol ID
Upgrade Protocol 0 = ## ## (S3C8+) (KM v8.31)
Code cannot be calculated...
End
This happens in two different PCs.
Cheers, |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Wed Feb 02, 2005 9:29 am Post subject: |
|
|
Alric wrote: | Something may be wrong with my set up because after loading the file and selecting the remote the parameters are not filled in automatically. | I'm able to open the file without any problems, so you might be doing something wrong. The upgrade is using the standard RC-5 protocol and should be useable on any remote. What remote are you trying to select? Are you following the correct procedure for loading the file in KM? How did you save the file to your local hard drive? _________________ Mark |
|
Back to top |
|
|
Alric
Joined: 01 Feb 2005 Posts: 4
|
Posted: Wed Feb 02, 2005 9:33 am Post subject: |
|
|
Thanks Mark for taking a moment to look at this.
This is where I may be doing something wrong. It is saved to my HD as a .txt file. I just save it straight from the link to my desktop.
I am using an 8910 and load the file using the load button on the spreadsheet.
Thanks! |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Wed Feb 02, 2005 4:39 pm Post subject: |
|
|
Alric wrote: | I just save it straight from the link to my desktop. | That might explain the problem. The best thing to do is right-click the link and then select Save Target As...
If that's what you did, then there's something else wrong, but I don't know what it would be. Have you opened any other upgrade files or is this your first attempt? _________________ Mark |
|
Back to top |
|
|
Alric
Joined: 01 Feb 2005 Posts: 4
|
Posted: Wed Feb 02, 2005 4:45 pm Post subject: |
|
|
Got it. Its a browser difference! If I save the file from IE it works fine. Initially, I was using Firefox in both computers.
On further inspection there are extra underscores in the Firefox saved files.
Thanks! |
|
Back to top |
|
|
|