JP1 Remotes

I want to "clone" the NevoC2 configuration. I have defined macros and activities. I want to make the Arrx18g the primary remote for the room. There does not appear to be a "master" remote specification on the (RMIR) "General" Tab. Instead, the remote is defined on each device definition.

Carl

Maybe Graham will correct me, but I don't think so. You'll have to re-do your macros and activities from scratch. I just open two instances of RMIR and put them side by side. Save each device, then change it to the 18G.

Thanks mdavej

Side by side is what I have been doing. One thing that would be nice, if the "Activity Macro Editor" could have a replace option, just like the "Macro" editor dialog form

Carl

mdavej wrote:Maybe Graham will correct me

Yes he will . The XSight Touch/Color, ARRX15G/18G and Nevo C2/C3 are essentially the same remote. If you save the setup of any of them as a .ir file by using File/Save As and changing the "Files of type:" drop-down selection to ""IR file (*.ir)", then you get a file in which the only thing that varies between these remotes is the [Signature] block at the beginning. You can open the .ir file with a text editor and edit this entry, which is the signature in ASCII code. For the Nevo C2 the value will be "55 53 42 38 30 30 36" for USB8006 and for the ARRX18G you need "55 53 42 38 30 30 35" for USB8005. You can get all the signatures from the names of the RDFs as they all begin with the signature. So edit this signature entry and load the edited file into RMIR. It should show up as the new remote and can be uploaded to it without further change. You lose any comments that are in the full .rmir file, but the setup itself is complete.

mathdon wrote:

mdavej wrote:Maybe Graham will correct me

Yes he will . The XSight Touch/Color, ARRX15G/18G and Nevo C2/C3 are essentially the same remote. If you save the setup of any of them as a .ir file by using File/Save As and changing the "Files of type:" drop-down selection to ""IR file (*.ir)", then you get a file in which the only thing that varies between these remotes is the [Signature] block at the beginning. You can open the .ir file with a text editor and edit this entry, which is the signature in ASCII code. For the Nevo C2 the value will be "55 53 42 38 30 30 36" for USB8006 and for the ARRX18G you need "55 53 42 38 30 30 35" for USB8005. You can get all the signatures from the names of the RDFs as they all begin with the signature. So edit this signature entry and load the edited file into RMIR. It should show up as the new remote and can be uploaded to it without further change. You lose any comments that are in the full .rmir file, but the setup itself is complete.

Why couldn't you do essentially the same thing by editing the rmir file then, and not lose any comments?

The Robman wrote:Why couldn't you do essentially the same thing by editing the rmir file then, and not lose any comments?

You can, but it is a lot more effort as both the name and signature of the remote occur multiple times in a .rmir file. If you want to keep two remotes in step, as CEDTV1999 seems to want to do, then you only want one master file in any case, and the simplest way to convert the setup to the other remote is through a .ir file as I described.

mathdon wrote:

The Robman wrote:Why couldn't you do essentially the same thing by editing the rmir file then, and not lose any comments?

You can, but it is a lot more effort as both the name and signature of the remote occur multiple times in a .rmir file. ...

Thanks guys for the details

I used Windows WordPad to look at the rmir file. That editor handles ASCII, so USB8006 is clearly shown. Redundant data has always been a trip-wire in my world
___________________

Carl