Page 1 of 1
Digivison DVT-3025EU
Posted: Thu Jun 12, 2014 12:13 am
by alanrichey
This is showing up as <unknown> in RM. I've uploaded a complete learn at
https://www.hifi-remote.com/forums/dload ... e_id=12560
Could someone help ?
Al
Posted: Thu Jun 12, 2014 11:02 pm
by 3FG
Alan,
I've seen this basic framing before: Lead In, 24 bits, Lead In, 16 bits, Lead Out, so I have an executor for it. However, the unit I looked at before had no name, so I didn't make a RMDU file for it.
So we can make a RMDU file for this. However, several of the learns weren't satisfactory. This protocol uses dittos and the following signals only contained the dittos, but not the actual signal. My experience has been that for a signal which repeats with dittos, it is very important to be sure that the teaching remote is stationary when learning. I have a tendency to click Capture, and then pick up the teaching remote and aim it at the Widget. I have to be careful to make sure the teaching remote is at the correct distance and not moving before I press the button. That way I can capture the very first part of the signal.
Whatever the cause, buttons 0, 3 ,6 ,Ch+, Exit, Up, Page+, and Page- only had dittos in the learns. Please re-learn these and I should be able to then post a RMDU file with the executor and OBCs.
Posted: Fri Jun 13, 2014 12:23 am
by alanrichey
That's great, thanks. New ICT file at
https://www.hifi-remote.com/forums/dload ... e_id=12563 contains 3 shots of each of those buttons.
Al
Posted: Fri Jun 13, 2014 10:33 pm
by 3FG
Here's a protocols.ini entry and
a test RMDU. Unfortunately, the OBCs from the learns give OBC=18 for both 6 and 9 and OBC=40 for Right and Menu. However, it may be worth giving this a try to see if the other codes are recognized or if we need to change to a single repeat.
Code: Select all
[Digivision]
PID=01 EF
DevParms=Dev1:8=78, Dev2:8=67, Dev3:8=79, Dummy:8
DeviceTranslator=Translator(lsb,0,8) Translator(lsb,1,8,8) Translator(lsb,2,8,16)
FixedData=00 00 00 FF
CmdParms=OBC:8=0
CmdTranslator=Translator(lsb,0,8)
DefaultCmd=00
Code.S3C80=43 8B 41 8B 16 C7 44 08 08 01 11 02 12 01 11 00 FA D2 DC 07 1C 03 70 FF FF FF 19 E4 07 06 60 07 77 77 F6 01 46 F6 01 0A 7B 01 AF E6 20 06 E6 21 E0 E6 28 C0 57 76 46 29 01 8D 01 46
Posted: Fri Jun 13, 2014 11:15 pm
by alanrichey
Thanks, will do. If you want to follow the discussion with the user it is over at
http://answers.slingbox.com/message/104440#104440 Let's hope after all your work he has the decency to reply.
Posted: Sat Jun 14, 2014 5:44 am
by alanrichey
All done and dusted, a very happy user
Thanks for your help. I'll upload the finished article.
Posted: Sat Jun 14, 2014 9:50 am
by 3FG
We have
seen this framing before, but with a different scheme for the meaning of the bits.
Here's a representation of the IRP for the Digivision:
Code: Select all
IRP = {38.0k,182}<3,-3|3,-6>(20,-10,Dev1:8,Dev2:8,Dev3:8,20,-10,F:8,~F:8,3,^108m,(20,-20,3,^108m)*)
The executor makes use of a feature of the IR engine: setting bit W7.3 enables a mid-frame burst (same as the lead in) after the initial PD13 bits.