JP1 Remotes

Thanks Capn (and thanks for the fast response)! Works perfectly!

Thanks for posting the PB file as well, maybe I can figure
out what was I doing wrong.. but I'm guessing it was pretty
much everything.

-Mongoloid-

PS: After looking at your work for a bit, I get it now.. So double thanks!

Greets all! I have been unable to create a protocol for a fan
I have. Here are working learned codes from a 2116 remote:

https://www.hifi-remote.com/forums/dload ... le_id=4529

Any help would be most appreciated.

Thanks.

Nope the 8060 extender wouldn't even upload to the remote.. Though
that could be due to the fact that the 8060 is a 4k..

Even with the extender, this remote's programming ability will be still limited anyway because of the hardwired EL control.

That part I don't mind so much, after playing some more.. I notice that even
the DSM protocol doesn't even work.. Now THAT hurts! I will try Nils
suggestion of the 8060 ...

I'll have to get back to you on that one.. I don't know if I want to bother
putting any more money in to it..

Is that as far as we go then?

Doh! Ignore my last statement about the second device and the animated Audio icon.. I had the VPT on..

After a little more playing with the Device combiner:

Any of the devices in the combiner will correctly send the first command
pushed then lock up with the transmit icon endlessly looping, rarely ...

Ok, the model on the PCB says "URC-11-8060-B00/B01 UEIS-10179".

My results from the Device combiner were, well not promising..

Of the 2 devices I put in:

The first sends the transmit icon in to a endless loop and remote
locks up.

The second (assuming I did not press anything from the first ...

I should have also mentioned that I have physically cut out the
the motion sensor. I don't see how that could matter, but I thought I
best mention it.

Mongoloid

Ok, I have uploaded the virgin dump:


http://f5.grp.yahoofs.com/v1/IF1AQhq8Kq9a7HaTNLCd5fVxdItVEC3zopusrdtL_X6UdxMpiK3DhDw8_Sy1jR0osqLQCc6wOjs_DSAD0IVl7xtS_ihFqRt1DA/Diagnosis%20Area/2133dump.txt


As far as useful info on the remote goes, printed on the bottom of the remote is:

Radio Shack ...

Hi Hal, and thanks for the quick response. I just gave it a try and I don't
see any difference, and yes I'll keep testing them as long as you wanna
keep working on it.

Thanks,
Mongoloid

Hi, I picked up a 2133 remote for kicks recently and proceeded to install
the Extender. I didn't get very far and after a quick poke around the board
here, I see someone else had my exact problem:

https://www.hifi-remote.com/forums/viewtopic.php?t=396&

Since this post was over a year old, I was ...

Greets all, I posted this in the beginner area.. (Probably not the best
place for it ). So I thought I'd try again and post a link to it in the
correct forum.

https://www.hifi-remote.com/forums/viewtopic.php?t=2142

Thanks.

Thanks, I found it by accident.. Yeah, it's done by same "Stereo Jack"
method as the 1993/2103.

Greets all, I'm in a pickle.. I just started wiring up a Radio Shack 15-2102
remote, I went ahead and cut the traces and such according to the
picture in the Yahoo group. I now notice that the picture only shows
5 wires, as the JP1 interface uses all 6 wires, and after further inspection
it can't be ...