| Function | Code | Instructions |
| Code Blink Back | 990 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 0. 4. PRESS 1, carefully COUNT the number of blinks. (1st digit) 5. PRESS 2, carefully COUNT the number of blinks. (2nd digit) 6. PRESS 3, carefully COUNT the number of blinks. (3rd digit) 7. PRESS 4, carefully COUNT the number of blinks. (4th digit) 8. PRESS 5, carefully COUNT the number of blinks. (5th digit), for remotes with 5 digit codes If the remote DOES NOT blink it means the number is 0. This is your setup code. |
| Code Search | 991 | 1. PRESS the button for the device you want to program, (TV,
VCR, CABLE, etc.), then RELEASE. 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. ENTER 9-9-1 (two blinks on the remote) 4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes. 5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device. |
| Volume Punch Thru | 993 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 3. 4. PRESS the device key you would like the volume to come from. Two blinks. To unlock volume control for a single device: 1. PRESS the device key you wish to unlock (AV1, AV2, etc.) - RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 3. 4. PRESS VOL-. Four blinks. 5. Repeat 1-4 to unlock other devices. To unlock all volume controls: 1. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 2. PRESS 9 - 9 - 3. 3. PRESS VOL+. Four blinks. |
| Copy one key to another | 994 | 1. PRESS and HOLD the SETUP button until the red LED flashes
twice, then RELEASE. 2. PRESS 9 - 9 - 4. 3. PRESS the DEVICE and the FROM button 4. PRESS the DEVICE and the TO button - two Blinks EXAMPLE: To use TV volume in the VCR mode, SETUP - 9 - 9 - 4 -TV - VOL UP - VCR- VOL UP - two blinks. You would have to do the same process for VOL DOWN and MUTE. NOTE 1: To assign as advanced code to a 'shift' key, simply press SETUP before pressing the key in step 4 above. NOTE 2: Functions cannot be copied to the device buttons or the SETUP button. |
| Assign Advanced Code | 994 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 4. 4. PRESS the SETUP button and then the three or five digit advanced code, depending on your remote. 5. PRESS the button you wish to use for that function - Two Blinks. NOTE 1: To assign an advanced code to a 'shift' key, simply press SETUP before pressing the key in step 5 above. NOTE 2: Advanced codes cannot be programmed to the device buttons or the SETUP button. NOTE 3: For 3 digit codes on a remote that expects 5 digits, add 2 zeros to the beginning of the code. To clear a key: 1. PRESS the device, (TV, VCR, CABLE, etc.), button - RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 4 4. PRESS the button you want to clear twice. - Two blinks. NOTE: To deleted a 'shift' key, press SETUP between the two presses of the button that you want to clear. |
| Macros | 995 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 9 - 5, two flashes. 4. PRESS the key that you want the Macro to be on (or PRESS twice to clear a macro key, then HOLD SETUP for two blinks) 5. PRESS the sequence of keys you want the remote to do (up to 15 keys) 6. PRESS "SETUP" and wait for two blinks - RELEASE. When you hit the key you put the macro on it will automatically start the sequence. NOTE 1: Macros can be assigned to any button, just remember that the macro will be assigned to this button in all device modes. NOTE 2: If you placed a macro on a button that you wish to restore to it's original function under certain device modes, you can re-program the button using the advanced codes. NOTE 3: Macros cannot be programmed to the device buttons or the SETUP button. The HD key can hold up to 5 macros. Each time you press HD, the next macro runs. |
| Learning | 975 | Line up your original remote and the head-to-head before
completing the following steps. 1. PRESS and HOLD the SETUP button until the red LED flashes twice. 2. PRESS 9 - 7 - 5, the red LED will flash twice. 3. PRESS the DEVICE key where you wish to learn the function. The next steps must be completed within 10 seconds. 4. PRESS the button that will receive the learned function, the LED will flash rapidly. 5. PRESS the button on the original remote to be learned. Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps). To test, press and release the device key in which the new feature was learned followed by the key on which the feature was learned. NOTE: To learn to a 'shift' key, simply press SETUP before pressing the key in step 4 above. |
| Delete Learned Function | 976 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 7 - 6 4. PRESS the button you want to clear twice. - Two blinks. NOTE: To deleted a 'shift' key, press SETUP between the two presses of the button that you want to clear. |
| Clear All Keys | 980 | 1. PRESS the device, (TV, VCR, CABLE, etc.), button -
RELEASE 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 8 - 0 -- Two blinks. |
| Restore Factory Defaults | 981 | 1. PRESS and HOLD the SETUP button until the red LED flashes
twice, then RELEASE. 2. PRESS 9 - 8 - 1 -- Two blinks. NOTE: This will erase all key moves, learned functions, device settings, etc. If the remote is an upgradeable remote, and has codes added, this will delete those codes also. |
| Shifted Keys | It is possible to store two commands on one button by using the
SHIFT key. The SETUP button acts as a shift key. When programming individual
buttons, whether by learning or by using advanced codes, if you press SETUP
before selecting the button where the command will be assigned, the function
will be stored on the shifted version of the button. Then when you wish to
use the button, press SETUP before you press the button. Shifted keys can be
used for learned commands, commands programmed using advanced codes and for
macros. NOTE: Shifted numeric keys: Program functions to shifted numeric keys using the procedure outlined above, but to actually use the shifted function you must press the SETUP button twice before pressing the numeric key, otherwise the remote thinks you are about to enter an advanced code. |
|
| Program Device Code | 1. PRESS the button for the device you want to program, (TV,
VCR, CABLE, etc.), then RELEASE. 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. ENTER the 5 digit code for your brand. 4. You should receive 2 quick flashes after entering your code. 5. PRESS the POWER button to test the code. (On VCR, LD, and CD players use PLAY) |
|
| Program My System | 979 | 1. PRESS the My System (MS) button, then RELEASE. 2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE. 3. PRESS 9 - 7 - 9. 4. PRESS the desired device key for the Transport keys, then PRESS PLAY. 5. PRESS the desired device key for the Volume keys, then PRESS VOL+. 6. PRESS the desired device key for the Channel keys, then PRESS CH+. 7. PRESS the desired device key for the Menu keys, then PRESS Menu. 8. PRESS the desired device key for the PIP keys, then PRESS PIP. 9. PRESS and HOLD the SETUP button until the red LED flashes twice, the RELEASE. |