MENU  •   Set Up  •   Getting Your Code  •   Changing Device Keys
Volume Punch Through  •   Advanced Functions  •   Clearing Out a Key

How to Program your One For All® remote

(Models URC-2001, URC-2060, URC-2062)

Set Up

After getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote.
  1. Press the device you want to program, then release.
  2. Press and hold the Magic button until the red LED gives a delayed blink.
  3. Continue holding the Magic button while you enter your 3 digit code.
  4. You should receive 2 quick flashes after entering your code.
menu

Getting Your Code

If you forget your code, the One For All ® will tell you using these simple instructions.
  1. Press the DEVICE (i.e.TV,VCR,etc) key that you want the code for - release.
  2. Press "Magic" and hold it down - you will see two blinks. Continue to hold down "Magic".
  3. While still holding "Magic", press the Device button, then press the "1" button. Count the number of time the remote blinks.
  4. Still holding "Magic", press the "2" button. Count the blinks.
  5. Still holding "Magic", press the "3" button. Count the blinks.
  6. Release "Magic".
NOTE: If the remote DOES NOT blink on one of the steps- it means the number is "0".
The three numbers you have make up the set up code of your device.

menu

Changing Device Keys

Suppose you want your One For All® to control a second TV?
You can turn the AUX key in to a TV key using the following procedure:
  1. Press the AUX key and release
  2. Press "Magic" (release) 9 - 9 - 9 - AUX - TV.
Your AUX key is now ready to be programmed with your TV code using the set up instructions.

You can change any of the device keys using this same method.

menu

Volume Punch Through

If you would like to access the TV volume through the CABLE key for convenience,
you would use the following procedure:
  1. Press the "CABLE" key, release.
  2. Press "MAGIC" (and release)
  3. Press 9 - 9 - 9 - TV - VOLUME +
You should now get volume in the CABLE mode.
You can punch through volume to VCR's using the same procedure.

menu

Advanced Functions

You can access advanced functions for your equipment using one of these two procedures.

Direct Access

  1. Find the three digit code for the advanced function you want.
  2. Press "MAGIC" (and release) and the three digit code.
  3. The function you desired will be performed on your device.

Key Magic

You can put the function on a key so you can access it with one stroke!
  1. Find the three digit code for the advanced function you want.
  2. Press "MAGIC" (and release).
  3. Press 9 - 9 - 9 -
  4. Press the button you want the function on.
  5. Press "MAGIC" (and release).
  6. Press the three digit code for the function you want.
  7. You will see two(2) blinks on the remote.
Now whenever you hit that key, the function will be performed on the device.
NOTE: you can program up to four(4) functions on keys.

menu

Clearing Out a Key

If you decide to change something you have put on a key, it is as simple as following these instructions.
  1. Press the Device key of the key you want to clear. (i.e. TV for TV volume)
  2. Press the "MAGIC" key (and release).
  3. Press 9 - 9 - 9 -
  4. Press the key you want to clear two (2) times.
  5. You will see two blinks on the remote.
Now the key is set back to its original function,

menu


All Material Copyright ® Universal Electronics Inc.
"One For All" copyright Universal Electronics Inc.
Any questions about the products should be directed to help@ueic.com