Page 1 of 1
Help Me With URC-39930RJ0-03 "Dreambox"
Posted: Thu May 17, 2007 11:34 am
by zubair4148
Hello I Have This URC-39930RJ0-03 Remote And It's Not Working On Dreambox but the With TV Code It Works Great. For Dreambox None Light Blinks While Pressing Keys.
I Made Jp1.2 interface Using This Guide Building a JP1.x Interface On This Site As It Is Tried Both 1.1 And 1.2 Connections And Cant Connect to the remote.
Tried JP1xTEST And Getting
**** NO JP1.x COMPATIBLE REMOTE FOUND! ****
please someone help me.
Posted: Thu May 17, 2007 2:01 pm
by Capn Trips
I recommend you read
THIS POST and use the referenced troubleshooting guide.
Posted: Sun May 20, 2007 9:30 am
by zubair4148
I Checked All It's From My Comport "DTR" Problem
Have To Try On Other PC.
Can Some One Please Tell Me Is It JP1, JP1.1 Or JP1.2
Posted: Mon May 21, 2007 12:37 am
by zubair4148
I Have A Remote For Dreambox
On The Back Of Remote Cover It's Printed
URC-39930BJ0-03
On The Board It's Printed
BV Olivic S08 2004 2-Mode Omega
URC-39930BJ0-XX
UEIS-10875 Rev: 01
39710-003-0001
REV: 01
Posted: Mon May 21, 2007 6:21 am
by The Robman
Posted: Mon May 21, 2007 7:53 am
by zubair4148
Finaly I Have Done It.
Thanks EveryOne For The Help.
Posted: Thu May 24, 2007 1:12 am
by zubair4148
Thanks For The Help I Got From This Forum.
Here Is My JP1.2 SMD Version
If Any One Needs Help I Will Be Here.
Problems with new DEAMBOX Universal-Remote URC-39930RJ0-03
Posted: Tue Jul 17, 2007 3:40 am
by Wolf123
zubair4148
Good morning.
I have a "Dreambox DM600PVR" with the new DREAM Universal Remote-Contoller URC-39930RJ0-03
And my TV is a "Medion-MD 21032" therefor is no Code in the Remote.
I think no problem it gives IR.exe and so on, and make me a JP1 interface... Nothing (no contact).
Look anyway to the internet and found it gives more then JP1 eg. JP1.x ahhh... that is it...
Make me a JP1.x interface, start IR.exe 703, but also nothing...
Load "JP1xTEST.exe" programm from Tommy Tyler and check the interface, all OK.
Fount A JP1.X COMPATIBLE REMOTE ON COM1!
Signature is 10381038
Memory Adress is $E000
Memory size is $1C00 (7168)
Now my question:
if i start IR.exe and check interface it write:
"Failed to open JP1.x interface".
Sometimes it write:
"Found JP1.x succest"
But if i then press "Download from Remote" it write:
"Failed to open JP1.x interface" or sometimes it write: "Read failed -1"
I have no idea what is wrong...
Have some one connect to this Remote-Controller an now what is my problem.
Regards
Wolfgang from Berlin (Germany)
RE: Problems with DEAMBOX Universal-Remote URC-39930RJ0-03
Posted: Tue Jul 17, 2007 5:27 am
by Wolf123
Hello Users,
i think i found the problem..
I build a hombrew JP1.x Interface by Tommy Tyler with Transistors.
On an other Computer the interface works now with IR.exe 703.
On a Dell-Laptop it works not.
I think it is better to take a MAX232 for TX and RX because the Data ar quicker from high to low.
Wolfgang
Re: RE: Problems with DEAMBOX Universal-Remote URC-39930RJ0-
Posted: Tue Jul 17, 2007 6:40 am
by The Robman
Congratulations Wolfgang. Could you explain the following line please, as I don't understand it.
Wolf123 wrote:I think it is better to take a MAX232 for TX and RX because the Data ar quicker from high to low.