Page 1 of 1
Radio Shack 15-2137 Help Needed
Posted: Wed Dec 20, 2006 8:53 am
by garytjia
I just purchased a radio shack 15-2137 universal remote and had it setup to work with Marantz SR7200 receiver. However, it does not have the component type input switch available (e.g. DVD, CD, DSS, etc.) to allow switching between different components for sound output. I am still learning how to program the remote. Does anyone know how I could program the remote to include the input switch function?
This is a continuation of this thread...
http://www.remotecentral.com/cgi-bin/mb ... d.cgi?5159
Thanks
Posted: Thu Dec 21, 2006 10:31 am
by kupakai
Welcome to this forum. Did you get the DVR functions (from your post in remotecentral.com) to work? I should have asked you first which device code you have set for the that, and if you have tried all of them.
As for the receiver, I'll ask the same question; what device code did you set it on, and did you try all of the listed ones?
Posted: Fri Dec 22, 2006 11:55 am
by garytjia
No, I have not tried all the listed device codes for Marantz receivers...I will try them out. Thanks.
Posted: Fri Dec 22, 2006 6:27 pm
by irs009
From what I've seen on these forums, and my own experience, the inputs often are found on the number keys. As you try all of the setup codes, be sure and check those for your inputs.
Jack
Posted: Sat Dec 23, 2006 3:06 am
by Capn Trips
It would be easier to provide you with detailed recommendations if you would use the mandatory template in the "Number 1 Code Search FAQ", linked in my sig below. Not knowing what setup code you are using makes it a bit harder to do so.
This file is an upgrade for your exact receiver. It has discrete input commmands. This upgrade uses the RC-5/5X combo protocol, used by built-in setup codes AUDIO/1089 and 1189, but the device codes are not identical.
It's also possible to generate about 2/3 of your device's signals using the RC-5 protocol, used in AUDIO/0189 (or possibly 0222 or 0269). I'm not sure whether the setup code you are using will support adding those commands via advanced code (EFC). If you're using AUDIO/1089 or 1189, here is the list of 5-digit EFCs:
Code: Select all
EFC Functions
31289 num 0
31293 num 1
31281 num 2
31285 num 3
31273 num 4
31277 num 5
31265 num 6
31269 num 7
31257 num 8
31261 num 9
29305 vol up
29309 vol down
29197 mute
31417 channel up
31421 channel down
28793 up arrow
28797 down arrow
28781 left arrow
28769 right arrow
28785 select
29345 sleep
31441 exit
29189 display
62149 Input: TV
06853 Input: VCR
66245 Input: DSS
53957 Input: LD
29281 BassUp
29285 BassDn
29273 TrebleUp
29277 TrebleDn
29361 S. Direct
29361 Source Direct
28785 Menu On
28789 Menu Off
31253 F/P
31237 DMode
31297 seek up
31301 seek down
31405 Stereo/Mono
31389 Memo
31381 Preset Scan
31373 FM
31361 AM
31365 LW
31429 Input: Tuner
30937 PTY
25285 Input: TAPE
37573 Input: CD
08901 Input: CDR/MD
60756 AUX
60820 DVD
03364 A/D
03332 6 CH IN
27684 Power On
27668 Power Off
35892 Mute On
35876 Mute Off
19508 Display
36404 Multi-Room
37172 Dolby/Prologic
39268 Test Tone
33060 Ch. select
33044 Ch Up
33028 Ch Down
33188 Dolby
33172 Night
33172 Night Mode
33156 ATT
33252 Auto
33236 DTS
35236 6-Stereo
35284 CS 5.1
35284 CS Mus
35268 DSP
60724 PL2-mov
60708 PL2-mus
60692 CS Cine
60726 AF
Depending on what setup code you are using, most of those codes should work (except likely the last one).
If you are using a different setup code, the EFCs might be different.
It would be really easy if you used JP1, but pending development of the rdf for the 2137, I'm not sure what more you can do or try.