View previous topic :: View next topic |
Author |
Message |
Hometheatremaven
Joined: 24 Mar 2006 Posts: 3
|
Posted: Fri Mar 24, 2006 7:52 pm Post subject: Are there some codes my OFA URC 7800 can't learn? |
|
|
I'm trying to get my OFA URC 7800 to learn the codes for my Sony STR-DB930; especially the code that turns the Surround Fields off and on. My OFA 8910 learned this code just fine but the URC 7800 just blinks once, meaning it can't learn the code.
Are there some codes the URC 7800 can't learn or are too long for the URC 7800?
Or have I somehow screwed up these learning buttons for my Audio device? The learning buttons work fine for my Toshiba 65H80 tv.
I need to know this before I go ahead and buy a JP1 cable and get into this whole JP1 programming thing.
One last question: Is it hard to solder the JP1 male header into the URC 7800? All it has is holes now. Is there anyplace that describes the soldering needed?
Thank so much. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21238 Location: Chicago, IL |
Posted: Fri Mar 24, 2006 10:04 pm Post subject: |
|
|
The 7800 should be able to learn everything that the 8910 can learn, but as long as one of the remotes can learn the signals in question, that's all you need to create a JP1 upgrade. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
MaskedMan Tivo Expert
Joined: 10 Feb 2004 Posts: 1006 Location: Boone, IA |
Posted: Sat Mar 25, 2006 12:08 am Post subject: |
|
|
You might have used up the learning memory on the toshiba tv. _________________ Edmund |
|
Back to top |
|
|
e.axel Exile Island Resident
Joined: 03 Feb 2006 Posts: 209
|
Posted: Sat Mar 25, 2006 1:49 am Post subject: |
|
|
Learning memory full?? |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21238 Location: Chicago, IL |
Posted: Sat Mar 25, 2006 9:12 am Post subject: Re: Are there some codes my OFA URC 7800 can't learn? |
|
|
Hometheatremaven wrote: | One last question: Is it hard to solder the JP1 male header into the URC 7800? All it has is holes now. Is there anyplace that describes the soldering needed? |
It's the easiest mod that you can do. I don't believe there is a write-up as there isn't much to write up.
Here's the step by step...
1) Remove the screw from the battery compartment and open the remote.
2) Apply some flux to the pads on the PCB where the 6-pin will go.
3) Put the 6-pin into the holes
4) Solder it.
5) Close up the remote and replace the screw.
If it's the soldering itself that is difficult, there are many guides to be found on the web. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
Hometheatremaven
Joined: 24 Mar 2006 Posts: 3
|
Posted: Mon Mar 27, 2006 4:51 pm Post subject: |
|
|
Robman:
Thank you so much for your help. I have now opened up the remote and am looking at the PCB board, and I see where the 6-pin will be inserted. There are 6 lanes (lines) leading from the area where the pins will be inserted, one for each pin. It's obvious that I don't want to get any solder between the lanes.
So I put some flux on the 6 holes in the PCB, then insert the pins. I assume that I put the flux on the side of the PCB where the lanes (lines) are. Is this right?
Now you say "Solder it". Where do I apply the solder so that I prevent it from crossing pins and lanes?
Sorry if this seems to be a stupid question but I've never done it and you've done it like a million times. I just don't want to screw it up! |
|
Back to top |
|
|
Hometheatremaven
Joined: 24 Mar 2006 Posts: 3
|
Posted: Mon Mar 27, 2006 5:10 pm Post subject: |
|
|
I think I understand now how to do it. I haven't received the 6 pin header yet, so I don't know what it looks like. But I now assume that it has pins going in 2 directions (front and back), with a board in between. The longer pins and the board go on the underside of the PCB with the shorter pins going through the holes in the PCB. Then I just put a tiny drop of solder on the pins going through the PCB.
Have I got it? |
|
Back to top |
|
|
|