JP1 Remotes Forum Index JP1 Remotes


FAQFAQ SearchSearch 7 days of topics7 Days MemberlistMemberlist UsergroupsUsergroups RegisterRegister
ProfileProfile Log in to check your private messagesLog in to check your private messages Log inLog in

LEGO power functions
Goto page Previous  1, 2, 3, 4, 5  Next
 
Post new topic   Reply to topic    JP1 Remotes Forum Index -> JP1 - General Forum
View previous topic :: View next topic  
Author Message
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Thu Dec 17, 2015 1:58 pm    Post subject: Reply with quote

Well, the binaries seem to match your earlier decodes on 12/15 except LLLL nibbles are reversed?

When I hold brake button down, it sends few bursts and stops. Ch1 blips are faster than ch4 blips which are spread out over time. And an extra longer spread after first 3 blips. Might correspond to "Transmitting Messages" in their .pdf.
I think brakes were in http://www.hifi-remote.com/forums/dload.php?action=file&file_id=13773
I can't hold the wheel. Each step stops the signal. But when I sweep around (posted some learns of single and sweeps before), it's a whole mess of blips.

I'll edit the protocol and will be back.
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Thu Dec 17, 2015 4:43 pm    Post subject: Reply with quote

6131 recordings via your new protocol
LEGO-3-newProtocol.zip in diagnosis: http://www.hifi-remote.com/forums/dload.php?action=file&file_id=13779
I ran 6 functions on ch1 and on ch4. Raw data is in the .txt files - should be easier to read than .rtf. Included .ict files as well.
One other .txt file is a screenshot of just brakes - I was looking for that spread of signals in the two channels, and think I don't see it.
I'll attempt to do binaries using your formulas, but it'll take me forever Sad

EDIT (8:40pm):
Rob, Your excel job was fantastic!
I compared binaries you did 12/15 from the LEGO remote, to my repeat recording today, and then what 6131 put out this afternoon.
Some goofy signals in my sets from today - post above. 6131 might not be 100% correct yet.
LEGO-ch1+4-(A-red)brake binaries-3sets.txt
http://www.hifi-remote.com/forums/dload.php?action=file&file_id=13780
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Thu Dec 17, 2015 11:02 pm    Post subject: Reply with quote

It's late now, so I will look at these tomorrow. Am I right in that you don't have the ability to test the signals on the Lego toy itself, at the moment?
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Fri Dec 18, 2015 8:18 am    Post subject: Reply with quote

I will have a chance to test your signals tomorrow morning Smile
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Sat Dec 19, 2015 4:24 pm    Post subject: Reply with quote

(1) PDF versions 1.00 and 1.10 look the same, but Version 1.20 (that 3fg posted, and Barf used) redefined some and added 7 more codes, which likely will end up in your xls(Main) and in KM as 105-111, and 121-127, assuming I follow how you made it. Reminder: the remote I play with has a 2008 date, so most likely 1.0 and 1.10 apply.
    Mode = Clear/Set/Toggle/Inc/Dec
    Data DDDD 0000 Toggle full forward (Stop ? Fw, Fw ? Stop, Bw ? Fw)
    0001 Toggle direction
    0010 Increment numerical PWM
    0011 Decrement numerical PWM
    0100 Increment PWM
    0101 Decrement PWM
    0110 Full forward (timeout)
    0111 Full backward (timeout)
    1000 Toggle full forward/backward (default forward)
    1001 Clear C1 (negative logic – C1 high)
    1010 Set C1 (negative logic – C1 low)
    1011 Toggle C1
    1100 Clear C2 (negative logic – C2 high)
    1101 Set C2 (negative logic – C2 low)
    1110 Toggle C2
    1111 Toggle full backward (Stop ? Bw, Bw ? Stop, Fwd ? Bw)

(2) All that is academic at this point. The train's receiver didn't hear or see one blip from 6131 Sad
Expected receiver behavior is that, just like the Widget, it blinks as soon as you touch a brake for instance.
I did 4 channels, 6 functions on each channel. Nothing blinked. Nothing moved. Yet the suff I recorded Dec.17 matches your codes.

(3) My son googled this out - Someone posted neat info about 8879(mine) as well as 8885 remotes, unfortunately undated.
http://www.hackvandedam.nl/blog/?page_id=559
Bunch of info differs from the PDFs.
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Sun Dec 20, 2015 12:12 pm    Post subject: Reply with quote

6131 aMMM and DDDD nibbles matched everything you did Dec.15. So I took a look at other stuff.
Lego remote sent different leadout on each channel, with ch4 being roughly 4x longer than ch1.
6131 all channels have the same leadout, around 101K.
Doesn't explain why didn't work at all, but might be part of the explanation.
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Sun Dec 20, 2015 6:24 pm    Post subject: Reply with quote

I guess I didn't look too closely at the checksum because it's not really an XOR of the previous 3 nibbles, it's actually the complement of an XOR, so one more instruction is needed in the executor.

Here's the updated protocol block:

Upgrade protocol 0 = 01 FF (S3C8+) Lego LPF RC Protocol (PB v4.02)
43 8C 11 8B 14 85 54 08 08 00 4F 01 00 00 4F 00
6F 13 88 00 4F 01 ED FF 05 76 00 01 6B 03 B6 03
08 28 03 F0 03 B4 04 C2 F0 04 B4 04 C2 18 04 56
C1 0F 44 C1 03 56 04 F0 60 C2 56 C2 0F 44 C2 04
8D 01 46
End

I will do some testing in a bit.
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!


Last edited by The Robman on Sun Dec 20, 2015 7:17 pm; edited 1 time in total
Back to top
View user's profile Send private message Visit poster's website
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Sun Dec 20, 2015 7:16 pm    Post subject: Reply with quote

Testing looks good, here's an updated zip file:
http://www.hifi-remote.com/forums/dload.php?action=file&file_id=13776
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Sun Dec 20, 2015 9:20 pm    Post subject: Reply with quote

Rob,
1. in the 1994 learned signals is A value, what is it?
2. in the PB setup Leadout OFF is 10000. Do you really mean it?
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Sun Dec 20, 2015 10:11 pm    Post subject: Reply with quote

VOL+ or CH+ = A-Brake (different toggle values)
VOL- or CH- = B-Brake

aux1 = ch1
aux2 = ch2
vcr = ch3
tv = ch4

i forgot about the long leadout that was required, that will take additional code as it's bigger than the regular executor can handle, and it would mean that I can't use the engine to generate the 5 repeats, I'd had to add code to do that too. That's more than I want to try to handle today, so will look into it later in the week.
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Sun Dec 20, 2015 10:22 pm    Post subject: Reply with quote

If that 10000 leadout in PB is related to the last number in the timing values, then 101-102k is for ch1, 138K for ch2, 180-181 for ch3, 222-223 for ch4. Sounds like a major PITA to code.

My re-recording 6131 and Lego remote confirms. 6131 signals don't show the spread of blinking between the five signals like I see on the Lego remote.

I will change 10000 to 101000 which, I think, will let me test ch1. Comments?

I keep forgetting: THANKS! this is the jp1-fun as we know it.
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Sun Dec 20, 2015 11:06 pm    Post subject: Reply with quote

ElizabethD wrote:
I will change 10000 to 101000 which, I think, will let me test ch1. Comments?

If you mean, you will change it in PB, that won't work because it's bigger than an executor can handle.X

If you want to try changing PB, what you need to do is:
1. change the JP to a CALL at the end of the code
2. add a step at the end that calls the pause routine, after first priming it with whichever of the 4 pause times you need.
3. Also, you would need to remove the fixed 5 repeats from the data block as that will need to be handled manually as a loop in the assembler.
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Mon Dec 21, 2015 12:25 am    Post subject: Reply with quote

Thanks again.
I took the lazy way out - changed hex to what you had in the last version or close to it. It puts out a long thing very close to what Lego remote does.
{just found the s3c8 asm commands list, so it would take me a century to do it right in PB).
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21210
Location: Chicago, IL

                    
PostPosted: Mon Dec 21, 2015 11:11 am    Post subject: Reply with quote

I originally had 1,000 in the leadout time before I increased it to 10,000. What hex code did I have that puts out 100,000 ?
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
ElizabethD
Advanced Member


Joined: 09 Feb 2004
Posts: 2348

                    
PostPosted: Mon Dec 21, 2015 11:29 am    Post subject: Reply with quote

Rob, $C738 puts out 101463-101490 for ch1.
I tried figuring how you did it: $C738 is 510000, double is 102K, and I suspect 500 more or less is for the high blip, resulting in 101.5.
Edit: If I follow this logic then ch2-4 will not fit in 16bits.
_________________
Liz
Tweeking 8910, HTPro/9811, C7-7800, 6131o, 6131n, AtlasOCAP-1056B01, RCA-RCRP05B and enjoying the ride Smile
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic       JP1 Remotes Forum Index -> JP1 - General Forum All times are GMT - 5 Hours
Goto page Previous  1, 2, 3, 4, 5  Next
Page 3 of 5

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


 

Powered by phpBB © 2001, 2005 phpBB Group
Top 7 Advantages of Playing Online Slots The Evolution of Remote Control