View previous topic :: View next topic |
Author |
Message |
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 7:27 pm Post subject: RCRP05B Extender - What does TV/OK Mean? |
|
|
Hi all. My first post.
I'm a beginner and bought an RCRP05B remote and cable and played with it somewhat.
I have read the JP1 for beginners, JP1-Just How Easy is It?, and the wiki on Extenders.
In the extender readme, the "TV/OK" button is mentioned for activation. What does TV/OK mean? TV followed by OK or both the TV and OK buttons at the same time? I tried loading the extender and now my remote does not respond to the setup hold.
I'm thinking the following three things to start with. Do these make sense?
1. One button to watch TV:
TV Power On
Set Input to TV
Receiver Power On
Set Input to TV
Remote Set to control volume and channel on TV
2. One button to listen to CD:
Receiver Power On
Set Input to CD
CD Power On
Remote Set to Control CD
3. One button Power Off:
TV Power Off
Receiver Power Off
CD Power Off
My equipment and software are hopefully in my signature. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30
Last edited by dannyo on Thu Jan 05, 2012 11:34 pm; edited 1 time in total |
|
Back to top |
|
|
vickyg2003 Site Admin
Joined: 20 Mar 2004 Posts: 7073 Location: Florida |
Posted: Thu Jan 05, 2012 7:30 pm Post subject: |
|
|
TV/Ok Means that you need to be in TV mode and then press the OK button. |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 8:40 pm Post subject: |
|
|
Thanks Vickyg
I wonder if the remote is trashed now. The setup hold does not produce any blinking lights. If I remove and replace a battery, the cable light blinks once if I hold setup then the cable light only blinks once. Can't seem to get it into 9xx mode to reset it.
Any ideas? _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30
Last edited by dannyo on Thu Jan 05, 2012 11:35 pm; edited 1 time in total |
|
Back to top |
|
|
eferz Expert
Joined: 03 Jun 2010 Posts: 1078 Location: Austin, Texas |
Posted: Thu Jan 05, 2012 8:52 pm Post subject: |
|
|
dannyo wrote: | Thanks Vickyg
I wonder if the remote is trashed now. The reset hold does not produce any blinking lights. If I remove and replace a battery, the cable light blinks once if I hold reset then the cable light only blinks once. Can't seem to get it into 9xx mode to reset it.
Any ideas? |
Have you tried new batteries? _________________ Remotes; JP1.2: Comcast URC-1067, JP1.3: Insignia NS-RC02U-10A, JP1.4 OARI06G, JP2.1: Cox URC-8820-MOTO (still trying to figure out how to make them self-aware.) |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 9:04 pm Post subject: |
|
|
Yes, new batteries. I even bought another remote this morning, down loaded it, saved and uploaded to the old remote. Still no action on setup-hold. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30
Last edited by dannyo on Thu Jan 05, 2012 11:36 pm; edited 1 time in total |
|
Back to top |
|
|
eferz Expert
Joined: 03 Jun 2010 Posts: 1078 Location: Austin, Texas |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 10:35 pm Post subject: |
|
|
vickyg,
My understanding is pressing and holding the setup should generate two blinks. It does nothing.
If I upload the image that was downloaded from the new remote, then pressing setup on the bad remote immediately gives one blink, then nothing. subsequent setup and setup holds generate no blinks.
The new remote gives two blinks after holding setup as expected. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30
Last edited by dannyo on Thu Jan 05, 2012 11:37 pm; edited 1 time in total |
|
Back to top |
|
|
vickyg2003 Site Admin
Joined: 20 Mar 2004 Posts: 7073 Location: Florida |
Posted: Thu Jan 05, 2012 11:04 pm Post subject: |
|
|
dannyo wrote: | Thanks Vickyg
I wonder if the remote is trashed now. The reset hold does not produce any blinking lights. If I remove and replace a battery, the cable light blinks once if I hold reset then the cable light only blinks once. Can't seem to get it into 9xx mode to reset it.
Any ideas? |
I don't use the JP1.3 extenders, but it is my understanding that these extenders activate and stay active until they are disabled.
The long hold of the SET buttons won't do anything until the extender is deactivated. |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 11:13 pm Post subject: |
|
|
Here is what the extender readme says:
"The extender is deactivated using a long-press of the "setup" key on the remote. The LED will flash 4 times to indicate that the extender has been deactivated and the remote has been returned to its normal, non-extended state"
Pressing and holding the setup produces no flashes. so it wont get out of extender if it was in it.
If it's ok with you, I will post on a new topic since this one has become off topic. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30
Last edited by dannyo on Thu Jan 05, 2012 11:33 pm; edited 1 time in total |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Thu Jan 05, 2012 11:32 pm Post subject: |
|
|
Sorry, I've been using the word "reset" instead of the "setup" button. I've meant "setup" in the previous posts. I finally got my magnifying glass out to check it. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30 |
|
Back to top |
|
|
mdavej Expert
Joined: 08 Oct 2003 Posts: 4501
|
Posted: Fri Jan 06, 2012 12:06 am Post subject: |
|
|
Please post your file(s). |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Fri Jan 06, 2012 12:34 am Post subject: |
|
|
How about some rmir files after I figure out how to post files?. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30 |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21237 Location: Chicago, IL |
Posted: Fri Jan 06, 2012 11:20 am Post subject: |
|
|
dannyo wrote: | ...after I figure out how to post files?. |
Follow the link at the top of the page to the File Section, then follow the link to the Diagnosis Area, then use the Upload button to load your files. When you're done, please post a link to the files here to save us all having to search for them. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
unclemiltie Expert
Joined: 21 Jan 2004 Posts: 1795 Location: Pittsburgh, PA |
Posted: Fri Jan 06, 2012 3:48 pm Post subject: |
|
|
The JP1.3 extenders do not deactivate when the remote is reset (by removing the batteries, this is well documented)
To deactivate, you MUST still have the extender loaded in memory. IF by some chance you loaded a non-extended IR file, you need to put back the extended IR file.
long press of setup should deactivate the extender on the RCA. (other JP1.3 remotes have different deactivation methods) _________________ this JP1 stuff is a sickness! |
|
Back to top |
|
|
dannyo
Joined: 31 Dec 2011 Posts: 42 Location: West Coast |
Posted: Fri Jan 06, 2012 7:38 pm Post subject: |
|
|
Robman,
Thanks for the tip on uploading. I found the upload button. I also found the BBCode link to the left of the reply box. Will try.
unclemiltie,
Thanks for the tip on overloading the extender. After I originally loaded the extender, it was acting goofy (Some display areas on the GUI were not being updated unless moused.) The overload was my mistake.
For now, I'll try to reload the extender so I can deactivate it. _________________ My equipment:
Remote RCA RCRP05B with JP1 2/3 cable.
Tivo Premiere
TV Sony Sony KDS-60A3000 (over the air)
Receiver Onkyo HT-R670 (part of HT-S6200 Theater sys)
CD player Sony CDP-C325
My Software:
RemoteMaster v2.04 build 14
RDF's as of 2011-01-14
Images and Maps Version 1.32 as of 2010-12-30 |
|
Back to top |
|
|
|