JP1 Remotes Forum Index JP1 Remotes


FAQFAQ SearchSearch 7 days of topics7 Days MemberlistMemberlist UsergroupsUsergroups RegisterRegister
ProfileProfile Log in to check your private messagesLog in to check your private messages Log inLog in

Rmir remote not found Urc-8910b02

 
Post new topic   Reply to topic    JP1 Remotes Forum Index -> JP1 - Beginners
View previous topic :: View next topic  
Author Message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Wed Aug 24, 2016 4:20 pm    Post subject: Rmir remote not found Urc-8910b02 Reply with quote

I have the JP1.x to JP1 adapter bought from Diygadget connected via my JP1.2 cable to pc serial connector.
Reading forum posts I see that I require jp12serial.dll bundled in jp12serial016.zip. This is from 2010. I have the latest Rmir installed do I still have swap the dlls in order for my remote to be found or is there another problem?
Tested it with jp1xtest and remote was found see
http://www.hifi-remote.com/forums/dload.php?action=file&file_id=14182
With rmir however remote is not found
All above was carried out without replacing the dll
Back to top
View user's profile Send private message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Thu Sep 01, 2016 4:20 pm    Post subject: Reply with quote

No ideas???
Back to top
View user's profile Send private message
mdavej
Expert


Joined: 08 Oct 2003
Posts: 3602

PostPosted: Thu Sep 01, 2016 4:59 pm    Post subject: Reply with quote

What version of RMIR exactly?

Can you post a link to the JP1.2 cable you have? If you built it, can you post a link to the schematic?

My only guess at this point is maybe the JP1 adapter is designed for JP1.2/3 and not JP1.1/2. Need to figure out which version of JP1.2 you actually have.

Do you have a JP1.3 cable you could try?
Back to top
View user's profile Send private message
3FG
Expert


Joined: 19 May 2009
Posts: 3224

PostPosted: Fri Sep 02, 2016 1:06 am    Post subject: Reply with quote

I'm not convinced that jp1xtest found a remote. Your PNG file doesn't show a signature, and the 2048 EEPROM size is the default value. I suspect that jp1xtest has only actually found the adapter. Are you sure it isn't rotated 180 degrees on the remotes 6 pin connector?
Back to top
View user's profile Send private message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Fri Sep 02, 2016 2:07 am    Post subject: Reply with quote

Thanx for reply
The cable works fine with j1.3 remotes which I have rcrp05br and Atlas 1056b01
The adapter is installed as per instructions from DYIGADGET.
One question regarding 8910b02 --I assumed pin #1 is the pin next to label JP1 on pcb board--looking at remote from rear side with 6 pin connector below battery compartment I assumed pin#1 to be the right top pin. Am I correct?
Back to top
View user's profile Send private message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Fri Sep 02, 2016 3:43 pm    Post subject: Reply with quote

the rmir version is 2.03 build 14
Can I rotate the adapter 180 degrees without doing damage--I am pretty sure that I assembled it as per DYIGADGET's instructions but one never knows...?
Back to top
View user's profile Send private message
3FG
Expert


Joined: 19 May 2009
Posts: 3224

PostPosted: Fri Sep 02, 2016 9:18 pm    Post subject: Reply with quote

I don't own a 8910, but at least some JP1 remotes have white outline around the 6 pins and one corner of the white outline is beveled. The unusual corner is adjacent to pin 1. I don't know if an incorrect rotation would cause damage or not.

Also, it occurs to me that you might be using JP1xtest with a very old version of JP12Serial. Support for the adapter was added in version 0.15. Perhaps using an older version may provide an invalid response.
Back to top
View user's profile Send private message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Sat Sep 03, 2016 1:52 am    Post subject: Reply with quote

I am using the file called testgroup.zip downloaded from forum file area --when I run the .bat file I get version 0.00---is there another file somewhere?
Back to top
View user's profile Send private message
3FG
Expert


Joined: 19 May 2009
Posts: 3224

PostPosted: Sat Sep 03, 2016 9:50 am    Post subject: Reply with quote

I'm referring to JP12Serial.dll. JP1xtest was written and distributed before the JP1 adapter was developed. So in the folder containing jp1xtest replace the old JP12Serial.dll with one copied from the Windows-x86 subfolder in your RMIR folder.
Back to top
View user's profile Send private message
smbs



Joined: 27 Mar 2012
Posts: 58

PostPosted: Sun Sep 04, 2016 1:36 am    Post subject: Reply with quote

Tried replacing dll but get same original message
Thanx
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic       JP1 Remotes Forum Index -> JP1 - Beginners All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


 

Powered by phpBB © 2001, 2005 phpBB Group
Get Smart! the band's official homepage Rockabilly Central