Data read back differs from data written

prelude · Post by **prelude** » Wed May 25, 2005 1:14 pm

Just talked to Doug from delcom.

He is testing the fix now.... unfortunately, this cannot be fixed in the USB driver... however it can be fixed in the IR.exe application.

I will keep you guys updated.

prelude wrote:Thank you very much!

Not sure if delcom can fix the problem by releasing a new USB driver....

Herbie wrote:Just replied to your PM, but for the benefit of everyone else:

My 100% flawlessly working interface reports as such:

Version 9
12/9/2002

Hope that helps, sorry to hear you have problems.

Filebug · Post by **Filebug** » Wed May 25, 2005 6:37 pm

The USB problem is being addressed and a fix will be available shortly. Thanks for your patience.

Lomala · Post by **Lomala** » Wed May 25, 2005 8:48 pm

Sorry just got back to this. My firmware for my non working cable is
SN 5685
Version 11 3/23.2005

I sent an email also to the one early in the post.

Thank you.

prelude · Post by **prelude** » Wed May 25, 2005 8:53 pm

Thank you!

Lomala wrote:Sorry just got back to this. My firmware for my non working cable is
SN 5685
Version 11 3/23.2005

I sent an email also to the one early in the post.

Thank you.

xraydoc · Post by **xraydoc** » Wed May 25, 2005 9:17 pm

My NON-working JP1 USB cable is:

SN: 5695
Version: 11 3/23/2005

Any idea when a fix is going to be available?

After finally figuring out the KM and IR programs and tweaking the remote I can't get the the data uploaded. It's driving me crazy!

Plus my wife thinks I'm an idiot for spending all this $ and all I got so far is headaches.

Any help appreciated.

prelude · Post by **prelude** » Thu May 26, 2005 4:53 am

Doug at delcom was testing a fix yesterday, Not sure what the fix would be... it seems we need to modify IR.exe .... anyways, don't worry, this will be resolved.

xraydoc wrote:My NON-working JP1 USB cable is:

SN: 5695
Version: 11 3/23/2005

Any idea when a fix is going to be available?

After finally figuring out the KM and IR programs and tweaking the remote I can't get the the data uploaded. It's driving me crazy!

Plus my wife thinks I'm an idiot for spending all this $ and all I got so far is headaches.

Any help appreciated.

prelude · Post by **prelude** » Thu May 26, 2005 7:47 am

Hi all:

The problem of the USB chip is fixed. Delcom will release a new frimware: version 12 to fix the problem. If anyone bought the USB kit/cable from diygadget.com, please contact me for a replacement.

The detailed information is posted in the following thread:

http://www.hifi-remote.com/forums/viewtopic.php?t=4632

Thanks

IdahoSnowDragon · Post by **IdahoSnowDragon** » Thu May 26, 2005 9:12 am

My new USB cable shows

SN# 5694
Version 11 3/23/2005

Trying to upload to URC-8910 using IR 6.00

Lomala · Post by **Lomala** » Thu May 26, 2005 4:18 pm

So there is no way to fix this issue via software? We are limited to hardware replacement?

prelude · Post by **prelude** » Thu May 26, 2005 6:34 pm

You are right

Lomala wrote:So there is no way to fix this issue via software? We are limited to hardware replacement?

wires10 · Post by **wires10** » Sun Dec 15, 2013 11:20 am

NEVER MIND!

Found this driver and all is fine!

--------------------------------------------------------------------------

I'm having the same problem (Data read back differs from data written) using IR 8.04.

For years everything has been working fine but I got a new receiver and am now using a different laptop(Dell E6420). The problems I'm having integrating the new receiver are an issue for another post. I'd like to get IR working on the new laptop running Win 7 32 bit.

Tried all the Delcom drivers, currently using version 4.7.0.0

USB_WIN.EXE reports:
SerNo: 24107
Ver: 16 11/16/2005

This JP1 interface (slightly oversized black heatshrinked USB plug with 3' blue ribbon cable) works fine on my older laptop (Dell D830) running XP SP3.

What to do?

JP1 Remotes

Data read back differs from data written

Problem is fixed

Same Problem