I am programming a 15-2117 for a Mit CS 2724R that I just aquired and have tried the EFC from the Advanced Code section for TV 0150 to try to get discrete commands for input as well as on/off but they don't work. Before I throw in the towel and assume that this model, circa 1991, doesn't have discrete access I figured I'ld ask for any advice/suggestions.
Thanks,
Mark
Discrete Commands On Old Mitsu
Moderator: Moderators
-
jon_armstrong
- Expert
- Posts: 1238
- Joined: Sun Aug 03, 2003 9:14 pm
- Location: R.I.P. 3/25/2005
- Contact:
Here is my list of every TV/0150 Mitubishi TV command that I have run across. Many of these probably came from the advanced code list at www.hifi-remote.com:
OBC EFC Function
000 181 1
001 185 9
002 183 POWER
007 186 CANCEL
008 053 2
009 057 0
010 055 CH +
011 059 A/V Reset
015 058 Ant A/B Toggle (will switch from other Input1-4)
016 117 3
018 119 CH -
023 122 SLEEP
024 245 4
026 247 Input-
027 251 INFO/Display
032 213 5
034 215 VOL +
040 085 6
042 087 VOL -
048 149 7
049 153 VGA
050 151 MUTE
052 148 Right
053 152 Enter
054 150 MOVE
056 021 8
058 023 TV/VCR, Input+
060 020 Left/SELECT
062 022 Zoom Toggle/ FORMAT
064 165 Vid
065 169 Up Arrow
066 167 Power On
069 168 INSTALL
072 037 Video
073 041 Down Arrow
074 039 Power Off (also EFC 189--OBC 128)
076 036 Ant B
080 101 ENTER/Audio (also EFC 229--OBC 88)
082 103 MENU
088 229 Audio
089 233 STB
090 231 Ant A
091 235 EXIT
097 201 Component 2
098 199 Input 1
099 203 GUIDE
101 200 Left Arrow
103 202 PiP Freeze
105 073 Component 1
106 071 Input 2
109 072 Right Arrow
111 074 Zoom Toggle (also EFC 022 --OBC 62)
113 137 ALTERNATE INPUT/DTV1
114 135 Input 3/DVD
119 138 PiP On/Off
119 138 PIP
121 009 DTV Input
122 007 Input 4/Front
127 010 SWAP
128 189 Power Off
If these still don't work, channel + usually always gets to tuner mode, so a macro for Ch+|Video Toggle is AV1, Ch+|Video Toggle|Video Toggle is AV2, etc.
OBC EFC Function
000 181 1
001 185 9
002 183 POWER
007 186 CANCEL
008 053 2
009 057 0
010 055 CH +
011 059 A/V Reset
015 058 Ant A/B Toggle (will switch from other Input1-4)
016 117 3
018 119 CH -
023 122 SLEEP
024 245 4
026 247 Input-
027 251 INFO/Display
032 213 5
034 215 VOL +
040 085 6
042 087 VOL -
048 149 7
049 153 VGA
050 151 MUTE
052 148 Right
053 152 Enter
054 150 MOVE
056 021 8
058 023 TV/VCR, Input+
060 020 Left/SELECT
062 022 Zoom Toggle/ FORMAT
064 165 Vid
065 169 Up Arrow
066 167 Power On
069 168 INSTALL
072 037 Video
073 041 Down Arrow
074 039 Power Off (also EFC 189--OBC 128)
076 036 Ant B
080 101 ENTER/Audio (also EFC 229--OBC 88)
082 103 MENU
088 229 Audio
089 233 STB
090 231 Ant A
091 235 EXIT
097 201 Component 2
098 199 Input 1
099 203 GUIDE
101 200 Left Arrow
103 202 PiP Freeze
105 073 Component 1
106 071 Input 2
109 072 Right Arrow
111 074 Zoom Toggle (also EFC 022 --OBC 62)
113 137 ALTERNATE INPUT/DTV1
114 135 Input 3/DVD
119 138 PiP On/Off
119 138 PIP
121 009 DTV Input
122 007 Input 4/Front
127 010 SWAP
128 189 Power Off
If these still don't work, channel + usually always gets to tuner mode, so a macro for Ch+|Video Toggle is AV1, Ch+|Video Toggle|Video Toggle is AV2, etc.
-Jon