How to get a Pronto learned power code to a JP1 remote ?

kenzo · Post by **kenzo** » Sat Oct 30, 2004 7:54 am

Hallo!

I have a Dreambox Sattelite reciever with an JP1 Connector.
The remote can control SAT & TV

I have 17" IIYAMA LCD Diplay with remote an need the power function of this.

I have a PRONTO in my house to so

and have lerned the PRONTO the code for POWER:
0000 006d 0022 0002 0156 00ab 0016 0015 0016 003f 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0015 0016 003f 0016 0040 0015 0015 0016 0040 0015 0040 0016 003f 0016 0040 0015 0040 0016 0015 0015 0040 0016 003f 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0040 0015 0015 0016 0015 0016 0015 0015 0040 0016 003f 0016 0040 0015 0040 0016 05c4 0156 0055 0016 0e4c

i have already soldered the cable for the JP1 it works
but i dont know know how i can get the code to the remote

could someone give me your help or may add the code for me in
IR.exe and mail me back the file.

this files i have downloaded from the remote
http://www.freakware.at/jp1/
the Power must be at Device #2 on the POWER BUTTON

I think here are many professionals here, i dont have the tools and the background, and must say that my engkish is not perfect and german newsgrousps are hard to find.

may email adress would be info@freakware.at

i hope for your help

thanks

Thomas Reiter
from AUSTRIA

Post by **The Robman** » Sat Oct 30, 2004 11:34 am

Download the IRTool and DecodeIR.dll programs, then use them to decode the signal. The results are that this is NEC1, device code 1 = 6, device code 2 = 251, OBC = 14 and EFC = 054

kenzo · Post by **kenzo** » Sat Oct 30, 2004 1:17 pm

that sounds easier for you than for me

do you have this programms already running on your system?

is it possible taht you can send me the saved file?

thomas

kenzo · Post by **kenzo** » Sat Oct 30, 2004 1:26 pm

what do you mean with irtool?

ir,exe?? the normal programm

i can only find Decode_IR_DLL.html

johnsfine · Post by **johnsfine** » Sat Oct 30, 2004 1:44 pm

kenzo wrote: I have 17" IIYAMA LCD Diplay with remote an need the power function of this.

Do you need only the power function? You don't plan to use any other function of that Display?

kenzo wrote: could someone give me your help or may add the code for me in
IR.exe and mail me back the file.

this files i have downloaded from the remote
http://www.freakware.at/jp1/
the Power must be at Device #2 on the POWER BUTTON

The Robman wrote:Download the IRTool and DecodeIR.dll programs, then use them to decode the signal.

If you only need that one command Rob did the part requiring IRTool and DecodeIR already and posted the answer.

The rest requires a simple upgrade created in KM or RM, and installed in IR and a KeyMove defined (also in IR) based on it.

kenzo wrote:that sounds easier for you than for me

I'm sure it would be.

The expert here tend to provide fast and helpful responses to anyone who tries to use the tools themselves and finds it too hard. The response is less consistent for those who just want it done for them. But someone MIGHT email you back a copy of your .ir file with that upgrade and KeyMove added. Hopefully they'll mention here that they did, so nobody else duplicates the task.

kenzo · Post by **kenzo** » Sat Oct 30, 2004 2:12 pm

yes

i would only need the power button inmy dreambox file
on device nr 2 TV

i plan not to do more with the JP1 remote
i have in my living room a Pronto for the other machines (this is my part)

may be you can help me

kenzo · Post by **kenzo** » Sat Oct 30, 2004 4:02 pm

i tried to install this programms

but have absolut no ideas how they work

this is totaly for freaks only

Post by **The Robman** » Sat Oct 30, 2004 5:56 pm

If it's just for freaks, what are you doing here? Might be time for you to seek help elsewhere.

Thanks for stopping by.

kenzo · Post by **kenzo** » Sun Oct 31, 2004 3:48 am

i realy try to lern it

i have now installed Remote Master

I select Dreambox as remote Device in Line

than i hav eentered the informations you have posted

and here

now i save it as .rmdu file

open IR.exe

"load from remote" and than

go the FIle and SET from RDF Path i think it wil now added

save it an send it back to the remote but without function

may be some ideas?

i only need that 1 silly power-code add. to my dreambox file

would give a nice helper a paypal thank, too

kenzo · Post by **kenzo** » Sun Oct 31, 2004 4:01 am

on the pronto this code works fine

0000 006d 0022 0002 0156 00ab 0016 0015 0016 003f 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0015 0016 003f 0016 0040 0015 0015 0016 0040 0015 0040 0016 003f 0016 0040 0015 0040 0016 0015 0015 0040 0016 003f 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0040 0015 0015 0016 0015 0016 0015 0015 0040 0016 003f 0016 0040 0015 0040 0016 05c4 0156 0055 0016 0e4c

johnsfine · Post by **johnsfine** » Sun Oct 31, 2004 5:39 am

You're pretty close.

1) On the Setup sheet of RM you need to type in a Setup code number (4 digit number less than 2048). It can be any setup code you're not using for other devices in that remote. You may also want to select a device type for it (or leave the default of cable).

2) After that is done, you must go to the output tab of RM and use the copy button to get that device upgrade to the clipboard. Then open your .ir file in IR.EXE and go to the devices tab, select Add and then press ^V to copy that upgrade from the clipboard into your configuration.

3) You shouldn't put the KeyMove into the external functions tab of RM, you should use the KeyMoves Tab of IR. Use "Add" there and then select the "bound" device mode and key where you want it to work. Then select the same device type and setup code as you used in step 1. Then type in the EFC of 054.

4) Save the configuration file from IR and upload it to the remote for testing.

kenzo · Post by **kenzo** » Sun Oct 31, 2004 6:01 am

1) On the Setup sheet of RM you need to type in a Setup code number (4 digit number less than 2048). It can be any setup code you're not using for other devices in that remote. You may also want to select a device type for it (or leave the default of cable).

ok that is clear

2) After that is done, you must go to the output tab of RM and use the copy button to get that device upgrade to the clipboard.

i will get

Upgrade cod 0 = 0f e2 (TV/0000) 1999 (RM v1.08)
5a 00 01 20 9f 20
End

Then open your .ir file in IR.EXE and go to the devices tab, select Add

her i get the

UPGRADE DEVICE POPUPSCREEN

i fill in the code and mut
select

Typ: Setup Code:
Protocol FF

and there is a field for Key Moves

what shoulkd i use here?!!?!

is this right ?!?

i dont understand how the remote will know a code only from this informations:

The results are that this is NEC1, device code 1 = 6, device code 2 = 251, OBC = 14 and EFC = 054

then press ^V to copy that upgrade from the clipboard into your configuration.

ok but,---

3) You don't put the KeyMove into the external functions tab of RM, you use the KeyMoves Tab of IR. Use "Add" there and then select the "bound" device mode and key where you want it to work. Then select the same device type and setup code as you used in step 1. Then type in the EFC of 054.

kenzo · Post by **kenzo** » Sun Oct 31, 2004 8:26 am

when i run the programm

ccf2efc i will recieve this informations

panel "1"
"TFT" "Learned" (NEC1):6.251:14 EFC=054
freq=38.0KHz
0000 006D 0022 0002 0156 00AB 0016 0015 0016 003F 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0015 0016 003F 0016 0040 0015 0015 0016 0040 0015 0040 0016 003F 0016 0040 0015 0040 0016 0015 0015 0040 0016 003F 0016 0040 0015 0015 0016 0015 0016 0015 0015 0015 0016 0040 0015 0015 0016 0015 0016 0015 0015 0040 0016 003F 0016 0040 0015 0040 0016 05C4 0156 0055 0016 0E4C

what should i do know with this ?!?!

whats the next step

johnsfine · Post by **johnsfine** » Mon Nov 01, 2004 3:23 pm

kenzo wrote: Upgrade cod 0 = 0f e2 (TV/0000) 1999 (RM v1.08)
5a 00 01 20 9f 20
End

Good

kenzo wrote: Then open your .ir file in IR.EXE and go to the devices tab, select Add

her i get the

UPGRADE DEVICE POPUPSCREEN

i fill in the code and mut
select

Typ: Setup Code:
Protocol FF

No. You should just use ^V in the big empty area at the top of that dialog. That should fill in the type ans setup code (and more) for you.

kenzo wrote: and there is a field for Key Moves

what shoulkd i use here?!!?!

Nothing. That is not the right KeyMoves dialog for this task.

Press OK after ^V, then switch to the KeyMoves tab and Add the KeryMove I described earlier.

kenzo wrote: i dont understand how the remote will know a code only from this informations:

The results are that this is NEC1, device code 1 = 6, device code 2 = 251, OBC = 14 and EFC = 054

It's MORE than enough information. The OBC is redundant with the EFC. You only need one or the other (depending on what program you are using).

The Pronto Hex you've posted in a long form of the same information. It doesn't carry any more information than "NEC1:6.251:14"

JP1 Remotes

How to get a Pronto learned power code to a JP1 remote ?

How to get a Pronto learned power code to a JP1 remote ?

Re: How to get a Pronto lerned poer code to a JP1 remote ...