Code for Remote Humax TivuMaxPro Satellite Decoder

ciaccino · Post by **ciaccino** » Wed Mar 11, 2015 4:31 am

1. What model Slingbox do you have? 350

2. Was there any error message after you typed in the Code and tapped the Test button? NO

3. Did you give the commands plenty of time to react? (I have a DVR that takes about 6-8 seconds to power up/down) YES

4. If you are using a Solo did you try both BIN files? TRIED BOTH FILES IN ANYCASE

5. After completing the setup do any of the buttons work? NO

6. If you are installing on a Solo or Pro-HD or older box that uses an external IR Blaster, have you used a Digital Camera or Mobile Phone Camera to confirm the IR Blaster is actually firing when you tap the Power button? (Watch the tip of the IR Blaster through the viewfinder while you tap a button. You should see a white (not red) flash. Test it on a real remote so you know what you are looking for). If you are using a 350/500 have you tried using the external blaster? YES IS ON

7. Have you experimented with the placement of the IR Blaster? On some devices this is critical so don’t give up too quickly. Try shining a flashlight at the front of the receiver and see if you can see the IR receiver behind the smoked glass.

8. Are you sure the device is working correctly using the real remote? YES

9. Are you sure your device is set to use IR ? Many boxes can operate on RF or IR and if it is set to RF then the Slingbox will not affect it.

10. If you have a device that supports multiple remote addresses (DirecTV, Dish Network, Tivo…) are you sure the remote address is set to the default ?

11. Have you tried resetting the Slingbox. ? This has been found to help. DONE TWICE SAME RESULT

12. Do you have access to a Logitech Harmony Universal Remote? If so let me know IF CAN BE USEFULL I WILL BUY ALSO FOR THE OTHER SLING BOX THAT I HAVE THE M1FOR AN OTHER SATELLITE RECEIVER

ciaccino · Post by **ciaccino** » Wed Mar 11, 2015 4:41 am

1. What model Slingbox do you have? 350

2. Was there any error message after you typed in the Code and tapped the Test button? NO

3. Did you give the commands plenty of time to react? (I have a DVR that takes about 6-8 seconds to power up/down) YES

4. If you are using a Solo did you try both BIN files? TRIED BOTH FILES IN ANYCASE

5. After completing the setup do any of the buttons work? NO

6. If you are installing on a Solo or Pro-HD or older box that uses an external IR Blaster, have you used a Digital Camera or Mobile Phone Camera to confirm the IR Blaster is actually firing when you tap the Power button? (Watch the tip of the IR Blaster through the viewfinder while you tap a button. You should see a white (not red) flash. Test it on a real remote so you know what you are looking for). If you are using a 350/500 have you tried using the external blaster? YES IS ON

7. Have you experimented with the placement of the IR Blaster? On some devices this is critical so don’t give up too quickly. Try shining a flashlight at the front of the receiver and see if you can see the IR receiver behind the smoked glass.

8. Are you sure the device is working correctly using the real remote? YES

9. Are you sure your device is set to use IR ? Many boxes can operate on RF or IR and if it is set to RF then the Slingbox will not affect it.

10. If you have a device that supports multiple remote addresses (DirecTV, Dish Network, Tivo…) are you sure the remote address is set to the default ?

11. Have you tried resetting the Slingbox. ? This has been found to help. DONE TWICE SAME RESULT

12. Do you have access to a Logitech Harmony Universal Remote? If so let me know IF CAN BE USEFULL I WILL BUY ALSO FOR THE OTHER SLING BOX THAT I HAVE THE M1FOR AN OTHER SATELLITE RECEIVER

alanrichey · Post by **alanrichey** » Wed Mar 11, 2015 3:33 pm

Q2. I'm a bit surprised you didn't get an error message when you tried the RV file.

Q7. You didn't answer.

Q12. The idea is that you install the device on the Harmony, probably by learning the codes. Then you tell me the details of your account and I load them onto my Harmony to look at the codes.

ciaccino · Post by **ciaccino** » Thu Mar 12, 2015 1:26 am

Q 7 It is Installed and next to the receiver but when i press from the sling box nothing blink

alanrichey · Post by **alanrichey** » Thu Mar 12, 2015 2:25 am

OK, I am still not convinced you have it next to the IR receiver in the box.

ciaccino · Post by **ciaccino** » Mon Mar 16, 2015 2:31 am

Don't know what to say it is next to it

alanrichey · Post by **alanrichey** » Mon Mar 16, 2015 4:07 am

No more suggestions then I'm afraid.

ciaccino · Post by **ciaccino** » Mon Mar 16, 2015 8:40 am

Thank