Fujitsu 4242 in Oz

Homer · Post by **Homer** » Wed Mar 17, 2004 3:19 am

I recently bought a MX500, OFA8811b & JP1 cable, with the hope of being able to place all of my devices onto the MX500, with discrete codes, macros etc etc for my home theatre stuff.

After many hours of work, I was able to sort out most of my devices but am having major troubles with my Fuijitsu plasma PDS4242 screen ( uses P-42RMO7 remote).

I have used IR/KM/Devices4 ( uses NEC1 protocol & 179 code) to make an upgrade, but this does not work. Also tried using KM & a file I found for Fuji4203 but still no go ( also NEC1 protocol).

Then made 8811 learn PowerOn, PowerOff & RGB from OEM remote & IR tells me that they are Fujitsu protocol & device no is 132 !! Would I be right in thinking that the Oz Fujitsu is using a different protocol ? Whereto now ?

Ta for a great forum

uwereinert · Post by **uwereinert** » Wed Mar 17, 2004 5:30 am

Homer wrote:IR tells me that they are Fujitsu protocol & device no is 132

That is the right protocol and device for your 4242!

Homer wrote:Whereto now ?

You should ask Fujitsu for an answer.

Learn all buttons of the original remote in to the 8811 und look in IR for the results. Create an upgrade via KM and don't forget to copy and paste the protocol since the Fujitsu protocol isn't in your remote yet.

Uwe

Post by **The Robman** » Wed Mar 17, 2004 7:03 am

The step by step is spelled out here:
http://www.hifi-remote.com/jp1/help

jon_armstrong · Post by **jon_armstrong** » Wed Mar 17, 2004 8:44 am

Here are the commands in my files for that model:

Fujitsu:132:001 EFC=185 Power On
Fujitsu:132:002 EFC=183 Power Off
Fujitsu:132:006 EFC=182 Video
Fujitsu:132:009 EFC=057 RGB dsub
Fujitsu:132:010 EFC=055 RGB bnc
Fujitsu:132:011 EFC=059 S-VIDEO
Fujitsu:132:012 EFC=052 COMPONENT
Fujitsu:132:014 EFC=054 RGB dvid
Fujitsu:132:016 EFC=117 shift 1
Fujitsu:132:032 EFC=213 volume up
Fujitsu:132:033 EFC=217 volume down
Fujitsu:132:048 EFC=149 shift 3
Fujitsu:132:062 EFC=022 cursor left
Fujitsu:132:063 EFC=026 cursor right
Fujitsu:132:064 EFC=165 shift 4
Fujitsu:132:065 EFC=169 cursor up
Fujitsu:132:066 EFC=167 cursor down
Fujitsu:132:091 EFC=235 set- ok
Fujitsu:132:128 EFC=189 wide

Homer · Post by **Homer** » Wed Mar 17, 2004 9:17 am

Thanks guys...upgrade now working although I had a problem in that IR only gave me a device number and was blank for sub-device. KM wanted both, so at 1st I just entered the default sub-device that KM prompted me with, but this did not work.
In desperation, I retried without a sub-device number & it worked

In due course I will save my file in your great files section.
Now off for some much needed beauty sleep & then gunna try to figure out how to make some discretes for those annoying toggle buttons.
Robs...just luv that new tut....much easier to follow than Tommy Tylers
Keep up the good work & thanks again.
If I catch you at Moes, I owe u 1 ...or 2

Homer · Post by **Homer** » Wed Mar 17, 2004 9:20 am

Jon....just spotted your reply. Looks like you gunna make life easy for me. Thanks a lot.

JP1 Remotes

Fujitsu 4242 in Oz

Fujitsu 4242 in Oz

Re: Fujitsu 4242 in Oz