| View previous topic :: View next topic |
| Author |
Message |
jeajea
Joined: 24 Feb 2010
Posts: 283
Location: USA
|
 Posted: Tue Feb 24, 2015 11:49 am Post subject: Charter URC-1060BC3 pause protocol |
 |
|
Is there a pause protocol for a Charter URC-1060BC3 remote (Maxim MAXQ610 processor)?
_________________
Jim Anderson |
|
| Back to top |
|
 |
3FG
Expert
Joined: 19 May 2009
Posts: 3367
|
| Posted: Wed Feb 25, 2015 1:41 am Post subject: |
|
|
In protocols.ini, add this line to [Pause Protocol (Special)] | Code: | | Code.MAXQ610=78 B4 01 04 00 00 D0 07 00 80 08 5A 00 00 00 58 FC D0 00 |
Entering a duration of 1 should give a delay of about 0.1 seconds. 255 gives 25.5 seconds, and 0 will give 25.6 seconds. |
|
| Back to top |
|
|
jeajea
Joined: 24 Feb 2010
Posts: 283
Location: USA
|
|
| Back to top |
|
|
3FG
Expert
Joined: 19 May 2009
Posts: 3367
|
| Posted: Wed Feb 25, 2015 3:57 pm Post subject: |
|
|
| I haven't looked at your files, but I suggest to first check if the Pause protocol works in a very simple setup. I tested using an Atlas 1056B03, made a Pause upgrade (the only upgrade) with Durations for functions 0 through 9, and assigned these functions to buttons 0 through 9. RMIR generated the keymoves for me. After uploading to the remote, pressing one of these buttons turned on the LED for the expected pause interval. I checked with a Widget that the remote does not transmit any IR, and also doesn't respond to button presses during the Pause. I did not try using macros, or shifted buttons. Perhaps that changes the behavior. |
|
| Back to top |
|
|
jeajea
Joined: 24 Feb 2010
Posts: 283
Location: USA
|
| Posted: Thu Feb 26, 2015 5:02 pm Post subject: |
|
|
I got pause to partially work.
Looks like RMIR has one or more problems with this remote
http://www.hifi-remote.com/forums/viewtopic.php?t=15980
Edit by mathdon: I see no problems in RMIR from the behaviour described in that thread. See my response in that thread.
_________________
Jim Anderson |
|
| Back to top |
|
|
3FG
Expert
Joined: 19 May 2009
Posts: 3367
|
| Posted: Fri Feb 27, 2015 1:34 am Post subject: |
|
|
Jim,
the following change isn't going to help your problem, but I want you to be aware that when the next protocols.ini comes out, the MAXQ executor for Pause will have different timing from the one I posted above. I had set it up so that it gave pauses in units of 1/10th seconds, but that doesn't match all the other Pause executors. I think we want to be able to use the same Pause RMDU files for all processors, so I've changed the executor to use units of 1/16th seconds. | Code: | | Code.MAXQ610=78 FF 01 04 00 00 E8 03 00 80 08 5A 00 00 00 58 FC D0 00 |
. |
|
| Back to top |
|
|
jeajea
Joined: 24 Feb 2010
Posts: 283
Location: USA
|
| Posted: Sat Feb 28, 2015 4:18 pm Post subject: |
|
|
Consider this
Pauses for an extended JP1.3 remotes are in 1/10 of a second units (0.1 0.5 9.5)
_________________
Jim Anderson |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
File Section
Wiki
