ClearPlay 747 HD

dspille · Post by **dspille** » Tue Apr 16, 2013 2:15 pm

1. Device: ClearPlay 747 HD
2. Type of device: DVD player
3. Year: 2011 (I think)
4. JP1/UEI Remote model: Atlas OCAP URC-1056 Black extended v2.10
5. Do you have a JP1 cable? Yes
6. Still have original remote? Yes
7. Checked the file section? Yes; none of the upgrades are recognized by my device
8. Checked Pronto file section (at R/C)? Yes; ClearPlay does not exist
9. Partially working setup code? Nothing partial
10. Learning remote question? n/a
11. Have you tried the JP1 Lookup Tool? Yes; doesn't exist there

Post by **vickyg2003** » Tue Apr 16, 2013 5:18 pm

7. Checked the file section? Yes; none of the upgrades are recognized by my device

Really?

The ClearPlay 427 HD upgrade in the section would be a problem for you to open, but Clearplay cp-427b is the same upgrade without the slingbox specific protocol. Give it another look.

http://www.hifi-remote.com/forums/dload ... le_id=7169

dspille · Post by **dspille** » Tue Apr 16, 2013 7:06 pm

I tried all three of the upgrades in the file section today, but my ClearPlay device is not responding to any of them. I just now tried the one you mentioned again, and it still does not work for me.

I'm not new this, although I was using older versions of the software. I was previously using an upgrade for a Panasonic Blu-ray player that I've replaced with ClearPlay device. I tried using IR801 RC3 with no success, but later today I've since been using the latest RM IR and it's still not recognized. I have been successfully using upgrades for my TiVo, LG TV, Sharp VCR & Onkyo receiver for a few years now, just recently replace my Toshiba TV with the LG with no difficulties. But I have spent many hours this afternoon with the ClearPlay with no success.

I did just order a Vizio VUR8 learning remote today to see if I can create my own upgrade. Not sure what's going on.

Post by **vickyg2003** » Tue Apr 16, 2013 8:15 pm

dspille wrote:I tried all three of the upgrades in the file section today, but my ClearPlay device is not responding to any of them. I just now tried the one you mentioned again, and it still does not work for me.

Hmm, that one SHOULD work. Often times there is a setting on DVD players to allow more than one unit to work in the same room. Is there anything in the manual that talks about a unit code?

If not could you post the non-working IR file (with a link here) so we can inspect it for common procedural errors.

dspille · Post by **dspille** » Tue Apr 16, 2013 8:32 pm

Here it is. Hopefully, it will provide some clues.

http://www.hifi-remote.com/forums/dload ... e_id=11853

Thanks,

Dennis

dspille · Post by **dspille** » Tue Apr 16, 2013 8:33 pm

Also, I could not find any unit code settings in the manual for the player.

Post by **vickyg2003** » Tue Apr 16, 2013 8:55 pm

Its a MACRO problem

Your DVD macro multiplexes between two different codes

DVD/VCR:1490 and DVD/VCR:0048

depending on short or long keypress. So the vcr/1998 is never used.

dspille · Post by **dspille** » Tue Apr 16, 2013 9:03 pm

Thanks. You were right! I guess that's what I get for having made things so complicated. I'd forgotten that I had done that a few years back. All is working now!

Now I just need to find some discrete on/off codes for this thing.

Thanks, again!

Dennis

JP1 Remotes

ClearPlay 747 HD

ClearPlay 747 HD

IR file

Thanks!