JP1 Remotes

I have the one for all urc-9910 bo1 rf/if extender with my viewing area in the living room and my equipment in another area.

I'd always have trouble getting this to work reliably. It seemed as though during the day it was a lot worse. I'd have to hit each key a couple of times before it would work ...

Thanks, that was quite helpful.

The 9910, b01 model was slightly different than described in that link.

There were only 4 screws on the pcb board at the top near the lcd surrounding a round object, likely the rf transmitter. Then there was a plastic button retainer cover that seemed to be able to ...

I've got a urc 9910 with a few keys that are real sticky. Can someone whose opened one up confirm the procedure. I'm the type who when opening up something electronic usually finds parts falling out that I can never figure out where they go.

Inside the battery holder there's 2 screws. Besides for ...

Hi, I found that the Robman had created an upgrade for another fan (Hawaiian Breeze fan) that seems the same, and I got it to work.

It's this one here
https://www.hifi-remote.com/forums/dload.php?action=file&file_id=3440

So, I'm all fat dumb and happy, but I read that I should delete the file I ...

vickyg2003 wrote:Check out this thread It might be helpful.

quite an understatement

All I had to do to get this one to work was to change rob's setting for the type of remote I have and it WORKS!!!!

thanks so much

I uploaded my .ir file here https://www.hifi-remote.com/forums/dload ... le_id=5563

The learned commands at the end (the last 2 CD keys on Power and Down) which IR says are Old Panasonic.

I'm stuck on how to proceed from here. I want to add these 2 to my extended 9910.

I found and installed a device upgrade for my rca vid switcher. That was easy once I remembered all the steps.

Now the hard part.

I've still not figured out how to get a device upgrade (or make one) for the fan. I was trying to figure out how to use KM, but I don't think IR is telling me enough ...

Thanks, I've uploaded the file and placed the link in the first post.

I have a URC 9910 which I've some time ago upgraded to an extender. I have the old pre-extender file. I reloaded the original pre-extend file, and learned 4 keys from 2 remotes. It did work, but inside ir.exe, I'm not sure DecodeIR (or the default) is decoding these correctly.

I uploaded the .ir ...

I'm using an extender. I have the 9910 remote. Is there some key sequence that will reset it to factory state, or do I have to upload my original saved state?

You want two remotes sharing one receiver?

The 8910 also lacks the RF transmit part inside the remote.


That was what I wanted, an extra 9910 remote, I already have 2 plus 2 receivers. I saw some sales on an 8910 and wondered if it was just an 9910 w/o the receiver.

So, is there a way to ...

Is the 8910 remote just the remote part of the 9910 remote/receiver combo?

I.E. Can I get a spare remote w/o a receiver by buying an 8910?

edit: putting the video-switch key in a macro, then it switches nicely by holding down the macro key.

I found the special prot functions, and coded into my macro a pause. But even $01 was then too long.

What did work was to create a macro (L3) that did 4 Dev_cancel's and call that for my pause ...

I have a urc 9910 and have just tried my first extender. I have one apparent timing issue, and was wondering if there was an easy way to change the overall speed of macro playback.

First, I have a radio shack video switcher that learns codes itself, so I can activate it using whatever remote ...

A few questions on key move vs. learned codes. I understand that learned codes use up a lot of memory, here are some other issues I was wondering about:

1. Are the learned codes sent out faster or slower than ones that are key mapped to an upgrade I can now create from the data supplied by ir.exe ...