JP1 Remotes

It's been 10 years now since creating this protocol for the JP1 remotes.

Recently, I bought a couple URC7935 Streamer to experiment since I no longer need multiple device remotes for everyday use. I still use my nearly 20 year old Elan equipment for audio amps in some room throughout the house ...

I remembered that I wrote an executor for this a while back called NEC 4DEV Yamaha Combo, so I have tried re-creating the original upgrade using that executor.

http://www.hifi-remote.com/forums/dload.php?action=file&file_id=26073

Yes! this works.

When you mentioned you were working on ...

The Robman wrote:Do keymoves work with the 2-byte version?

Yes. They work fine on the phantoms and discretes. There are a mix of device/sub that are on the main tab I need to incorporate functions. Right now I'm just running two device upgrades to cover it.

I understand now the signal structure now. Thank you. However, this upgrade limits you to one device/subdevice code at a time since it considers them fixed and the OBC1 and OBC2 as the variable.

Any more thoughts on why the 4-byte version isn't working for keymoves?

That appears to work. Thank you.

There's a couple functions I'll need to add, but all the functions responded in the test upgrade.

I was looking through the Yamaha Standard and Extended IR codes PDF, how did you establish the Hex values for this upgrade?

Thanks Rob.

I added this to protocol.ini and used your test upgrade to test the functions. The amp didn't respond to anything whether on standard buttons or keymoves.

Rob, Just a quick note: In Bill's extenders you don't uninstall them. You have to deactivate. IIRC in this RCA remote use LKP of Setup button.

jetskier, did you edit the rmdu file using correct RDF file?
I'll take a peek at your stuff later.

I did a 981 reset on another remote before I built the ...

I built a simple unextended remote upgrade with just the Yahama as AUD device. I put the discrete commands in the Macro1 & Macro2 buttons as well as a macro on the pip_ch+ and - buttons. Same behavior.

I ran the discrete on code through IR Scope. The discrete on for
"Main Zone" reports NEC1 ...

I just replaced my 1999 era Technics audio receiver with a new Yamaha TSR-7850 I purchased from Costco. I've been using the RCA RCRP05B Extender V1.05 for the past few years with no issues.

I found this upgrade in the file section for the older Yamaha receivers:

http://www.hifi-remote.com/forums ...

I got my cable from Tommy years ago. It's a JP1.2 for sure.

I've been using my 10820s and 8820s for years now. They have been great, but a few of them are starting to show signs of wear. The button labels are faded and the contacts are worn. I found a couple 10820s a few months back and snagged them. I know they've been out of production for years now ...

I don't have any Xsight remotes, but I've been using the 2.03 Alpha 21e RMIR and just noticed an issue with macros. I tried this with both a fresh setup and an existing RMIR file. When I go to macros and clone an existing or create a new, or edit existing, when I switch tabs to device let's say. The ...

Alright. This upgrade is tested and works awesome with the new LCD/Plasma proof IR receivers I just got. Before with the old IR receivers, I'd have to wait about 3-4 minutes for the TV's backlight to warm and stop emitting all the IR noise washing the old receiver. With the new IR receiver and this ...

Thanks Vicki. That was it. Those two settings were hiding from me the whole time!

Now it seems to work fine. The buttons 4- didn't work when I uploaded from IR, but the same upload from RMIR worked fine. I'm not sure what's going on there.

Now since I got this going. I may screw around with the ...

Oh. Another thing I am using the pulse version of my RM file for the template as the OBCs are the same. If you look at it, it uses the 5/6. I just noticed it has the Off as total set as well.

And one last thing. Thanks for your patience! I really appreciate your time as I am trying to understand ...